Ge 15260 In-Wall 30min Countdown Timer Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Horloge Ge 15260 In-Wall 30min Countdown Timer. GE 15260 In-Wall 30min Countdown Timer Manuel d'utilisation Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 1
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
AVERTISSEMENT
Risque de choc électrique
• Couper l'alimentation à la boîte à fusibles
ou au disjoncteur avant l'installation
• Ne pas utiliser à proximité de l'eau
• Pour utilisation intérieure uniquement
Risque d'incendie
• Ne pas dépasser les caractéristiques
électriques
• Utiliser seulement du fil en cuivre avec ce
dispositif
WARNING
Risk of electric shock
Shut off power at fuse box or circuit breaker
before installation
Do not use in wet locations
Use indoors only
Risk of fire
Do not exceed electrical ratings
Use copper wire only with this device
125VAC, 15A Résistivité
125VAC, 15A Usage Général
125VAC, 1250W Tungstène
125VAC, 1/2 HP
Ligne (CHARGÉE) — Noir
Neutre — Blanc
Charge — Rouge
Blanc
(Neutre )
Noir
(Ligne )
Neutre (Blanc)
Chargée (Noir)
Charge (Rouge)
A Charge
Noir
INSTALLATION :
À utiliser seulement avec des dispositifs à un commutateur unipolaires installés de façon permanente.
NE PAS DÉPASSER LES CARACTÉRISTIQUES NOMINALES DE LA MINUTERIE
1. Coupez l'alimentation à la boîte à fusibles ou au disjoncteur.
2. Retirez la prise murale actuelle et l'ancien interrupteur.
3. À l'aide d'un petit tournevis à lame plate, soulevez la plaque-couvercle avant d'une minuterie encastrée, à partir de
l'arrière de la minuterie, et conservez-la en vue de la repose.
4. Fixez bien les fils dans le mur aux conducteurs de la minuterie à l'aide des connecteurs verrouillés par rotation fournis.
5. Dénudez le fil de construction à 3/8 po.
6. Les connecteurs fournis sont à utiliser avec du fil en cuivre seulement.
7. Si un fil de terre est branché à la prise de l'ancien interrupteur, insérez un connecteur verrouillé par rotation à l'extrémité
du fil de terre et poussez le connecteur et le fil de terre à l'arrière du boîtier.
8. Montez la minuterie dans le boîtier avec le cadran orienté vers le dessus du boîtier. Fixez la minuterie au boîtier à l'aide
des vis de montage incluses.
9. Fixez en place par pression la plaque avant de la minuterie (enlevée à l'étape no 3) et réglez
l'interrupteur « ON » (marche), « OFF » (arrêt) et « Timer » (minuterie) de la minuterie à la
position OFF (arrêt).
10. Rétablissez l'alimentation à la boîte à fusibles ou au disjoncteur.
FONCTIONNEMENT :
La minuterie a trois réglages : ON (marche), OFF (arrêt) et TIMER (minuterie). Pour contrôler la
charge manuellement, placez l'interrupteur à glissière à la position « ON » (marche) ou « OFF
» (arrêt). Pour utiliser la minuterie :
1. placez l'interrupteur à glissière à la position « TIMER » (minuterie);
2. tournez le cadran dans le sens horaire jusqu'à ce que l'heure voulue s'aligne sur la flèche du
cadran central.
10
20
0
10
20
0
Line (HOT) — Black
Neutral — White
Load — Red
White
(Neutral)
Black
(Line)
Neutral (White)
Hot (Black)
Load (Red)
To Load
Black
125VAC, 15A Resistive
125VAC, 15A General Purpose
125VAC, 1250W Tungsten
125VAC, 1/2 HP
INSTALLATION:
For use only with single-pole, one-switch permanently installed devices.
DO NOT EXCEED THE TIMER RATINGS.
1. Shut off power to the circuit at fuse box or circuit breaker.
2. Remove current wall plate and old switch.
3. Using a small flat blade screwdriver pry off the front cover plate of in-wall timer, from the back of the timer and keep for
later installation.
4. Securely connect the wires in the wall to the timer leads with the twist-on connectors provided.
5. Strip building wire to 3/8”.
6. Supplied connectors for use with copper wire only.
7. If a ground wire was connected to the old switch plate put a twist on connector on the end of the ground wire and push
the connector and ground wire into the back of the box.
8. Mount the timer in the box with the dial toward the top of the box. Secure timer to box using the included mounting
screws.
9. Snap-on the timer face plate (removed in #3) and put the timer On – Off – Timer switch in
the off position.
10. Restore power to the circuit at fuse box or circuit breaker.
OPERATION:
The timer has 3 settings ON, OFF, and TIMER. To control the load manually, place the slide
switch in the “ON” or “OFF” position. To use the timer,
1. Place the slide switch in the “TIMER” position
2. Rotate the dial clockwise until the desired time lines up with the arrow in the center dial.
15260-1
Vue de la page 0
1

Résumé du contenu

Page 1 - AVERTISSEMENT

AVERTISSEMENTRisque de choc électrique• Couper l'alimentation à la boîte à fusibles ou au disjoncteur avant l'installation• Ne pas utiliser

Commentaires sur ces manuels

Pas de commentaire