Ge 15313 GE 7-Day In-Wall Digital Timer Manuel d'utilisateur télécharger pdf

Programming On/Off Events: (up to 4 ON/OFF program)

1. Push “Setup/PGM” twice. “P1” will ﬂash on screen.

2. Push + or - to choose the desired program to change, or start at “P1 ON.”

Push enter to conﬁrm which program P1, P2, P3, or P4 you are setting.

3. Push + or - to choose between “set” or “del” program. Push enter to conﬁrm.

4. Push + or - to choose the desired days you would like the timer to activate.

The options are;

• S, M, T, W, Th, F, S (All days)

• S, S (Weekend)

• M, T, W, Th, F (Weekdays)

• M through S: (Individual days)

• T, Th

• M, W, F

Push enter to conﬁrm the days of week setting.

5. Push + or - to choose the desired hour. Push enter to conﬁrm.

6. Push + or - to choose the desired minute. Push enter to conﬁrm.

7. After completion of steps 1 to 6 the ON time and days selected are

complete. Repeat steps 4 to 6 to set the OFF time for the program.

8. Once ON and OFF for a program is chosen the timer will ask you to “save”

- push enter to save program, then continue to set other programs. When

ﬁnished programming push Setup.

Note: The display will show “AUTO” to alert you a program is running.

*When done programming, close door. You cannot exit during a program cycle.

Using Random Feature: The random feature will turn lights on and off using

the programmed times + or - 30 minutes. This gives your house a more lived in

appearance.

1. Push the random button to activate random feature. The screen will change

from “AUTO” to random. Screen will display “RDM”

2. Push the auto button to deactivate random mode. Screen will display “AUTO”

Ratings:

120VAC 60Hz

Incandescent (Tungsten): 5A/600W

Resistive: 15A/600W

Maximum Temperature: 40°C

Manual Override:

Manual override will not effect programing.

Pressing the door will override the timer

setting and will manually turn the switch ON

and OFF.

Memory Back Up: This timer is equipped

with memory back up that will protect the

settings for up to 60 minutes. You never have

to replace batteries. The internal backup

requires about 12 hours to fully charge.

ON - OFF Slide Switch: Turns power to the

timer ON or OFF. In “OFF” position timer will

not function manually or automatically.

ON = Power to timer & ﬁxture.

OFF = No power to timer or ﬁxture.

For normal operation leave in the on

position.

Digital Timer

If you are unsure or unclear about this installation, contact

a qualiﬁed licensed electrician. Not for use with CFL or

ﬂuorescent bulbs. Use with incandescent, xenon, halogen.

Safety ground (green) must be connected for proper

operation.

Installation Instruction

1. Turn OFF the main power at the circuit breaker.

2. Remove the existing switch.

3. Connect the wires of the timer to the wall box as shown in Figure 1 and

Figure 2 using the wire nuts provided.

a) Connect the line wire to the black wire from Timer.

b) Connect the load wire to the blue wire from Timer.

c) Connect the ground wire to the green wire from Timer.

Note: Be sure that all wire nuts are secure.

4. Tuck the wires into the wall box leaving room for the timer. Using the screws

provided, mount the timer to the wall box being careful not to crush any

wires.

5. Turn main power ON at the circuit breaker.

POWER-UP SEQUENCE: If you don’t see the numbers on the screen you will

want to verify the unit is wired correctly, the unit is getting power, and the bulb

in the ﬁxture is good.

Verify the Power slide switch inside the button is set to the ON position. See

Figure 3.

Note: If the timer has no display check the bulb ﬁrst to make sure the light bulb

is screwed in tight and not burned out. A working light bulb must be installed

to complete the circuit.

1. Open the door by inserting a ﬁngernail or screwdriver in the space provided

at the top of the door and pulling forward. See Figure 4.

2. Position the Power switch to ON (To Right Side). Display will not appear until

switch is on. See Figure 3.

3. Push and hold the RESET button for 3 seconds. The word Reset will appear

on the screen. NOTE: When adjusting settings on timer, always use a non-

metallic, insulated tool such as a toothpick or wooden pencil.

4. The display should ﬂash 12:00 am.

Setting Current Day & Time:

1. Push Setup/PGM once, date will appear on screen.

2. Push the + or - to move the arrow under the current day of the week (S, M, T,

W, T, F, S). Press enter to conﬁrm. See Figure 5. Hour will appear on screen.

3. Push the + or - to scroll through the Hours. Press enter when the correct

hour is found, minutes will appear on screen. Press the + or - to scroll

through the minutes. Press enter when the correct minute is found to

conﬁrm setting. Be sure (AM/PM) is correct. This is located in the lower left

portion of the display.

15313

03-10-2011

www.jascoproducts.com

Typical Wiring Schematic

Black

Load

White

Blue

Line

= Wiring Nut

Ground

Green

Timer

Figure 1

Figure 3

Figure 4

Figure 5

Figure 2

Green

Blue

(Load)

Black

(Line)

Black

Ground

1 2

Digital Timer 1
Temporizador Digital 2

Résumé du contenu

Page 1 - Digital Timer

Programming On/Off Events: (up to 4 ON/OFF program)1. Push “Setup/PGM” twice. “P1” will ﬂash on screen.2. Push + or - to choose the desired program

Page 2 - Temporizador Digital

3. Presione + o - para desplazarse por las horas. Presione Enter cuando encuentre la hora correcta; aparecerán los minutos en la pantalla. Presione +

Commentaires sur ces manuels

Pas de commentaire

Ge 15313 GE 7-Day In-Wall Digital Timer Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Horloge Ge 15313 GE 7-Day In-Wall Digital Timer. GE 15313 GE 7-Day In-Wall Digital Timer User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Horloge Ge 15313 GE 7-Day In-Wall Digital Timer