GE GTD45EASJWS Fiche technique télécharger pdf

Listed by

Underwriters

Laboratories

GTD45EASJ

Series 7.2 Cu. Ft. Capacity Aluminized Alloy Drum Electric Dryer with HE Sensor Dry

Specification Created 7/15

5.7 cu. ft. Dryers

Back View

Power

Cord Hole

30-1/2

5.8, 6.0 and 7.0 cu. ft. Dryers

Back View

Power

Cord Hole

4-1/2

Power Cord LoCations

BaCk View

side View rear View

eLeCtriC dryer rating:

240V 5600W 24A 60Hz

208V 4400W 22A 60Hz

exhaust oPtion: 4-way rear, right, left and bottom

CirCuit requirements: An individual, properly-grounded

branch circuit, protected by a 30-amp circuit breaker or a time-delay

fuse, is required.

note: Dryer wall outlet must be located within 36" of service cord

entry and acessible when dryer is mounted in position.

instaLLation information: For complete information, see

installation instructions packed with your dryer.

dimensions and instaLLation information (in inChes)

sPeCiaL instaLLation requirements

aLCoVe or CLoset instaLLation:

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.

• The dryer MUST be exhausted to the outside.

• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:

0" either side; 3" front and rear

• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".

• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of

open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a

minimum of 120 sq. in. of open area equally distributed.

• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

Bathroom or Bedroom instaLLation:

• The dryer MUST be exhausted to the outdoors.

• The installation must conform with the local codes, or in the absence of local codes, with the

National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

minimum CLearanCes other than aLCoVe or CLoset instaLLation:

• Minimum clearances to combustible surfaces are: 0" both sides; 3" rear

dryer exhausting information : Use metal duct only, vertical and horizontal ducting.

22 1/2"

29 1/2"

27"

3 1/2"

1 3/4"

3 1/4"

37 1/2"

44"

27"

Power Cord 4 1/2"

11 3/4"

Side View

Rear View

For answers to your Monogram,

GE Profile

™

or GE

appliance questions, visit our website

at geappliances.com or call GE Answer Center

service, 800.626.2000.

1 2 3

Résumé du contenu

Page 1 - GTD45EASJ

Listed by Underwriters LaboratoriesGTD45EASJ GE® Series 7.2 Cu. Ft. Capacity Aluminized Alloy Drum Electric Dryer with HE Sensor DrySpecification Crea

Page 2 - GE Dryer Vent

Specification Created 7/15for ComPLete information, see instaLLation instruCtions PaCked with your dryer.duCting materiaLs: For best performance, this

Page 3 - GTD45EASJWS_GTD45GASJWS

Specification Created 7/15GTD45EASJWS_GTD45GASJWSfeatures and BenefitsHE Sensor Dry – Keep your clothes looking and feeling their best. Dual thermisto

Plus de documents pour Sèche-linge électrique GE GTD45EASJWS

Voir le document GE GTD45EASJWS Spécifications rapides

GE GTD45EASJWS Spécifications rapides (3 pages)

Commentaires sur ces manuels

Pas de commentaire

GE GTD45EASJWS Fiche technique

Naviguer en ligne ou télécharger Fiche technique pour Sèche-linge électrique GE GTD45EASJWS. GE GTD45EASJWS Spec Sheet Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Sèche-linge électrique GE GTD45EASJWS

Commentaires sur ces manuels

Produits connexes et manuels pour Sèche-linge électrique GE GTD45EASJWS