GE GTD65EBSJWS Fiche technique télécharger pdf

Listed by

Underwriters

Laboratories

Specification Created 7/15

For answers to your Monogram,

GE Profile

™

or GE

appliance questions, visit our website

at geappliances.com or call GE Answer Center

service, 800.626.2000.

GTD65EBSJ

Series 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Electric Dryer with HE Sensor Dry

22 1/2"

30 1/2"

27"

3 1/2"

1 3/4"

3 1/4"

38 1/2"

46"

27"

Power Cord 4 1/2"

11 3/4"

Side View Rear View

5.7 cu. ft. Dryers

Back View

Power

Cord Hole

30-1/2

5.8, 6.0 and 7.0 cu. ft. Dryers

Back View

Power

Cord Hole

4-1/2

Power Cord LoCations

side view

BaCK view

rear view

eLeCtriC dryer rating:

240V 5600W 24A 60Hz

208V 4400W 22A 60Hz

exhaust oPtion: 4-way rear, right, left and bottom

CirCuit requirements: An individual, properly-grounded branch circuit,

protected by a 30-amp circuit breaker or a time-delay fuse, is required.

note: Dryer wall outlet must be located within 36" of service cord entry and

acessible when dryer is mounted in position.

instaLLation information: For complete information, see installation

instructions packed with your dryer.

dimensions and instaLLation information (in inChes)

Special Installation Requirements

aLCove or CLoset instaLLation:

- If your dryer is approved for installation in an alcove or closet, it will be stated

on a label on the dryer back.

- The dryer MUST be exhausted to the outside.

- Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:

0" either side; 3" front and rear

- Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.

- Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in.

of open area equally distributed. If this closet contains both a washer and a dryer, doors must

contain a minimum of 120 sq. in. of open area equally distributed.

- No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

Bathroom or Bedroom instaLLation:

- The dryer MUST be exhausted to the outdoors.

- The installation must conform with the local codes, or in the absence of local codes, with

the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

minimum CLearanCes other than aLCove or CLoset instaLLation:

- Minimum clearances to combustible surfaces are: 0" both sides; 3" rear

dryer exhausting information : Use metal duct only, vertical and horizontal ducting.

1 2 3

Résumé du contenu

Page 1 - GTD65EBSJ

Listed by Underwriters LaboratoriesSpecification Created 7/15For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website

Page 2 - Best PerformanCe

Specification Created 7/15For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at geappliances.com or call GE Answ

Page 3 - GTD65EBSJ_GTD65GBSJ

Specification Created 7/15gtd65eBsJ GE® Series 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Electric Dryer with HE Sensor Dryfeatures and BenefitsENERGY