GE MGA Guide d'installation télécharger pdf

Straight Stanchion Cover (See Figure 6)

Attach mounting arm onto conduit. Hang ballast housing

on cover by hinge. Proceed to Wiring.

35-201578-T8 (1/00 GELS)

IF MULTIWATT:

Multiwatt ballasts are available in various combina-

tions of wattage. See wiring instructions on wiring

tag inside the luminaire.

BALLAST HOUSING INSTALLATION

Swing unit shut. Tighten ballast cover screw securely.

LAMP INSTALLATION

Angle Stanchion Cover (See Figure 7)

Attach mounting arm onto conduit. Hang ballast housing

on cover by hinge. Proceed to Wiring.

B.WIRING:

Cut incoming supply conductors to six (6)

inches inside cover. Route conductors through lead

clip provided and make electrical connections,

including ground as shown on wiring label (See

Figure 8).

CAUTION

Risk of burn

• Allow lamp/fixture to cool before

handling

Make all electrical connections in accordance with

the National Electrical Code and any applicable local

code requirements.

Verify that supply voltage is correct by comparing it

to nameplate.

When changing voltage on reconnectable units,

move only the lead with the insulated connector.

IF SINGLE VOLTAGE:

All single voltage ballasts are pre-wired such that

user need only connect the supply conductors.

IF MULTIVOLT: (120/208/240/277 volts)

Connect the ballast lead with the insulated terminal

to the desired voltage terminal as indicated on the

ballast terminal nameplate.

Figure 5

Figure 6

Figure 7

Figure 8

Use only lamps specified on nameplate. Observe

lamp manufacturer’s recommendations and restric-

tions on lamp operation, particularly ballast type,

burning position, etc.

Lamp Tightness – Medium Base Lamp: The lamp should be

tightened to a light firmness sufficient to depress the center

contact.

OPTICALS

CAUTION: GLOBE IS TEMPERED GLASS. DO NOT

SCRATCH OR CHIP.

Attach globe by threading firmly into bottom of ballast

housing.

Prismatic Refractor Assembly

Type V, R or L

Thread adapter firmly into ballast housing. To orient

asymmetrical glass, loosen clamping screws, turn glass and

retighten screws. To relamp, unscrew complete optical from

ballast housing.

ACCESSORIES

External Reflector

Insert mounting screws. Orient reflector to proper position

and slip over mounting screws. Turn reflector and tighten

screws securely.

Globe Guard

Insert protective guard into ballast housing and turn until

retained by detent.

MAINTENANCE AND CLEANING

It will occasionally be necessary to clean optical assembly

in order to maintain light levels. Frequency of cleaning will

depend on dirt levels in user’s facility and minimum accept-

able light levels . Reflector should be cleaned with any

suitable, non-abrasive solution of water and soap or deter-

gent. Residual cleaning agent should be removed with clean

water rinsing. Glassware may be cleaned with any conven-

tional glass cleaner. If unit gets soiled on the inside, it should

be cleaned and any damaged gasket or filter replaced.

MOUNTING ARM

COVER

MOUNTING

SCREWS

CUSTOMER LEADS

WIRING

BOX

TETHER

BALLAST HOUSING

CUSTOMER LEADS

BALLAST

HOUSING

COVER

WIRING BOX DOOR

CUSTOMER LEADS

BALLAST HOUSING

COVER

MOUNTING ARM

SET SCREW

LEAD CLIPS

GEH-5754A

Mini•Gard Luminaire

INSTRUCTIONS

®Registered Trademark of General Electric Company

THE OPERATING TEMPERATURE “T-CODE” LISTED

FOR THIS LUMINAIRE IS BASED ON THE FOLLOWING

BULB SIZES. USE OF OTHER THAN THESE MAY

RESULT IN A HIGHER OPERATING TEMPERATURE

AND COULD RESULT IN A HAZARDOUS CONDITION.

LAMP TYPE WATTAGE BULB SIZE

HIGH PRESSURE SODIUM 70,100,150 ED 23 1/2

HIGH PRESSURE SODIUM 250, 400 ED 18

METAL HALIDE/MERCURY 175, 250 ED 28

METAL HALIDE/MERCURY 400 ED 37

AVERTISSEMENT: COUPER L’ALIMENTATION

AVANT L’INSTALLTION OU L’ENTRETIEN.

GENERAL

A complete luminaire consists of a ballast housing,

optical assembly, and a cover/mounting.

CAUTION: When installing luminaire in

hazardous locations check operating temperature

limits prior to installation to insure it conforms to

the environmental temperature restrictions and

NEC classifications.

MOUNTING INSTALLATION

Flexible Cover (See Figures 2 and 3)

Loosen four(4) bolts holding mounting hub to cover.

Position adapter plate correctly to balance luminaire. Use

widest bolt spacing possible to secure plate to cover. Hang

ballast housing on cover by hinge. Proceed to Wiring.

WARNING

Risk of electric shock

• Turn power off before servicing

– see instructions

Ceiling Cover (See Figure 4)

Using the slotted tabs, mount cover to ceiling. Hang

ballast housing on cover by hinge. Proceed to Wiring.

Figure 2 Figure 3

Figure 4

CAUTION

Unit will fall if not installed properly

• Follow installation instructions

Pendant Cover (See Figure 1)

Thread cover onto conduit. Orient cover and seal around

conduit using approved NEC procedures. Tighten set screw

at mounting hub. Hang ballast housing on cover by hinge.

Proceed to Wiring.

READ THOROUGHLY BEFORE INSTALLING

Figure 1

BALLAST HOUSING

CUSTOMER LEADS

COVER

.875

ADJUSTMENT

CUSTOMER LEADS

BALLAST HOUSING

MOUNTING HUB

COVER

Bolt pattern

for lower

wattages

Bolt pattern

for higher

wattages

GROUND

SCREW

BALLAST HOUSING

CUSTOMER LEADS

COVER

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in

connection with installation, operation or maintenance. Should further information be desired or should particular problems arise which

are not covered sufficiently for the purchaser's purposes, the matter should be referred to General Electric Company.

Wallmount Cover (See Figure 5)

Mount wiring box provided and pull leads. Tether is

supplied to hold arm assembly while connecting supply

leads. Attach arm assembly to wiring box. Do not damage

gasket attached to arm assembly. Mounting screws should

be tightened in alternate sequence. Hang ballast housing

on cover by hinge. Proceed to Wiring.

GE Consumer & Industrial

Lighting Systems

East Flat Rock, NC 28726

GE Consumer & Industrial

Lighting Systems

3010 Spartanburg Highway

East Flat Rock, NC 28726

(828) 693-2000

www.gelightingsystems.com

1 2

Mini•Gard Luminaire 1

Résumé du contenu

Page 1 - Mini•Gard Luminaire

Straight Stanchion Cover (See Figure 6)Attach mounting arm onto conduit. Hang ballast housingon cover by hinge. Proceed to Wiring.35-201578-T8 (1/00 G

Page 2

Straight Stanchion Cover (See Figure 6)Attach mounting arm onto conduit. Hang ballast housingon cover by hinge. Proceed to Wiring.35-201578-T8 (1/00 G