Ge 26730 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Téléphone sans fil à combiné Ge 26730. GE 26730 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
INTRODUCTION
Your Caller ID phone stores and displays specific
information, provided by your local telephone company, to
subscribers of Caller ID or similar caller identification
services. You must subscribe to one of these services in
order to use this unit.
Your Caller ID phone enables you to:
Identify callers before you answer the phone.
View the time and date of each incoming call.
Record up to 40 Caller ID messages sequentially.
Know who called while you were away.
To get the most from your new phone, we suggest that you
take a few minutes right now to read through this user's
guide.
IMPORTANT: In order to use this feature, you must
subscribe to either the standard Name/Number Caller
ID Service or Caller ID with Call Waiting Service. To
know who is calling while you are on the phone, you
must subscribe to Caller ID with Call Waiting Service.
IMPORTANT: Because cordless phones operate on
electricity, you should have at least one phone in your
home that isn’t cordless, in case the power in your
home goes out.
BEFORE YOU BEGIN
PARTS CHECKLIST
Make sure your package includes the items shown here.
MODULAR JACK REQUIREMENTS
You need an RJ11 (CA11A) type modular
jack, which is the most common type of
phone jack and might look like the one
pictured here. If you don’t have a modular
jack, call your local phone company to find
out how to get one installed.
INSTALLATION NOTE: Some cordless telephones
operate at frequencies that may cause interference to
nearby TVs and VCRs. To minimize or prevent such
interference, the base of the cordless telephone
should not be placed near or on top of a TV or VCR. If
such interference continues, move the cordless
telephone farther away from the TV or VCR.
DIGITAL SECURITY SYSTEM
Your cordless phone uses a digital security system to
provide protection against false ringing, unauthorized
access, and charges to your phone line.
When you place the handset in the base, the unit verifies
its security code. After a power outage or battery
replacement, you should place the handset in the base for
about 20 seconds to reset the code.
INSTALLATION
DESKTOP INSTALLATION
NOTE: For desktop charging only, the handset is able
to charge facing up or down.
1. Place the handset in the base.
2. Raise the base antenna.
3. Plug the power supply cord into an AC outlet. The
CHARGE/IN USE indicator comes on indicating that the
battery is charging.
Allow the phone to charge for 12 hours before
using the first time. If you don't charge the phone
properly (for 12 hours) when you first set up the
phone, performance of the battery will be
compromised.
4. After charging, connect the telephone line cord to the
wall jack.
5. Set the RINGER switch on the handset to ON.
NOTE : The phone automatically defaults to touch-
tone dialing. To change to pulse (rotary) dialing, see
“Tone/Pulse Dialing”. If you don’t know which type of
service you have, check with the phone company.
WALL MOUNT INSTALLATION
Because it is necessary to charge the handset for 12 hours
prior to connecting the phone for use the first time, it is
better to leave the unit on a flat surface during initial
charge before attempting to hang it on the wall.
1. Place the handset in the base.
2. Plug the power supply into an AC outlet.
The CHARGE/IN USE indicator comes on indicating that
the battery is charging.
Allow the phone to charge for 12 hours before
using the first time. If you don't charge the
phone properly (for 12 hours) when you first set
up the phone, performance of the battery will be
compromised.
3. Set the RINGER switch on the handset to ON.
4. After charging, plug
the telephone line
cord into the wall jack.
5. Attach the mounting
bracket by inserting
the two tabs at the top
and then snapping the
tab at the bottom into
place.
6. Slip the mounting
holes over the wall
plate posts and slide
the unit down firmly
into place. (Wall plate
not included.)
7. Raise the base
antenna.
NOTE : The phone automatically defaults to touch-
tone dialing. To change to pulse (rotary) dialing, see
“Tone/Pulse Dialing”. If you don’t know which type of
service you have, check with the phone company.
CORDLESS PHONE BASICS
RECEIVING A CALL
1. Check the display to see who is calling.
2. Press the TALK button.
MAKING A CALL
To make a call, press the TALK button before you dial and
press it again to hang up.
REDIAL
Press the REDIAL button to redial the last number you
dialed, (up to 32 digits).
FLASH
Use the FLASH button to activate custom calling services
such as call waiting or call transfer, which
are available through your local phone company.
TIP: Don’t use the TALK button to activate custom
calling services such as call waiting, or you’ll hang up
the phone.
CHANNEL BUTTON
While talking, you might need to manually change the
channel in order to get rid of static. Press and release the
CHANNEL button to advance to the next clear channel.
TEMPORARY TONE
This feature enables pulse (rotary) service phone users to
access touch-tone services offered by banks, credit card
companies, etc., by pressing the TONE button to
temporarily make the phone touch-tone compatible. To get
information about your bank account, for example, you
would:
1. Call the bank’s information line.
2. Press the TONE button (*) after your call is answered.
3. Follow the voice instructions to complete your
transaction.
4. Hang up when finished. The phone returns to pulse
(rotary) service.
FINDING THE HANDSET
This feature helps to locate a misplaced handset.
Press the PAGE/FIND button on the base. The handset
beeps continuously for about 2 minutes or until you press
any button on the handset.
RINGER SWITCH
The RINGER switch must be ON for the handset to ring
during incoming calls.
TONE/PULSE DIALING
This adjustment allows you to select tone (touch-tone) or
pulse (rotary) mode dialing. The phone is automatically set
for touch-tone use.
TONE
1. Make sure the phone is OFF.
2. Press and hold the CHANNEL button for 2 seconds until
the phone beeps.
3. Press TONE*
PULSE
1. Make sure the phone is OFF.
2. Press and hold the CHANNEL button for 2 seconds until
the phone beeps.
3. Press #.
VOLUME
The VOLUME button controls the volume of the handset's
earpiece.
VOICE MESSAGING
Provided your phone
company offers voice
messaging service and
you subscribe to it, the
CHARGE/IN USE
indicator on the base
flashes when the
phone is not in use to
indicate there is a
message waiting. It
stops flashing after the
message has been
reviewed.
DIALING A CALLER ID NUMBER
1. Make sure the phone is OFF.
2. Use the arrow (* and #) buttons to display the desired
Caller ID record.
3. Press CALL BACK. The number dials automatically.
CHANGING THE NUMBER FORMAT
The FORMAT button lets you change the format of the
displayed number. The available formats are as follows.
7-digit 7-digit telephone number.
10-digit 3-digit area code + 7-digit telephone
number.
11-digit long distance code “1” + 3-digit area code+
7-digit telephone number.
1. Use the arrow buttons (* and #) to scroll to the number
you want to call back.
2. If the number will not dial as shown, press the FORMAT
button. Repeat if necessary, until the correct number of
digits are shown.
3. Press CALL BACK. The number dials automatically.
NOTE: To clear the local area code, press and hold
CHANNEL until AREA CODE appears. Then enter
"000".
MEMORY
Store up to ten 24-digit numbers in memory for quick
dialing. This memory feature is in addition to the 40 Caller
ID records that can be stored in the Caller ID memory log.
STORING A NUMBER IN MEMORY
1. Make sure the phone is OFF.
2. Press the MEMORY button.
3. Press the memory location number (0-9).
4. Press MEMORY again. The display shows
ENTER NAME.
NOTE: If you don't want to enter the name, skip step 5.
5. Use the keypad to store a name (up to 15 characters).
More than one letter or character is stored in each of the
number keys. For example, to enter Joe Smith, press 5
for J; press 6 three times for O; press 3 two times for E;
press 1 to enter a space before you start entering the
last name; press 7 four times for S; press 6 for M; press
4 three times for I; press 8 for T; and 4 two times for H.
If you're using two letters consecutively that are stored
in the same number key, you must press FORMAT
between the letters. For example, if you enter Barb,
press 2 two times for B; press FORMAT; press 2 for A; 7
three times for R; and 2 two times for B. You need to
press FORMAT between the B and the A since they are
stored within the same number key.
6. Press MEMORY. The display shows
ENTER TEL NUMBER
.
7. Use the keypad to enter the number you want to store
(up to 24 digits). To add a pause, See Inserting a Pause
in the Dialing Sequence.
8. Press MEMORY again to store the number.
9. Record whose number is stored in the location on the
memory label provided. You will also be able to view
the name and number in the display.
WARNING:
TO PREVENT FIRE
OR ELECTRICAL SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE EXCLAMATI
O
POINT WITHIN T
H
TRIANGLE IS
A
WARNING SI
G
ALERTING YOU
O
IMPORTAN
T
INSTRUCTION
ACCOMPANYIN
THE PRODUC
T
THE LIGHTNING
FLASH AND ARROW-
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USER-
SERVICEABLE PARTS IN-
SIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
Base
Handset
PAGE/
FIND
CHARGE/
IN USE
Mounting bracket
1
2
3
ABC DEF
5
4
6
JKL
GHI
MNO
8
7
9
PQRS
WXYZ
TUV
0
TONE
OPER
PHONE
#
TALK
REDIAL
CALL BACK
VOLUME
DELETE
CHANNEL
FORMAT
MEMORY FLASH
OFF
ON
RINGER
1
3
2
4
5
1
2
3
Time
Date
Caller ID name
Number of calls
Caller ID phone number
3175554231
10:51
A.M.
8/11
REPT
CALL
NEW
MEMO
#
25
SMITH JOHN
PAGE/
FIND
CHARGE/
IN USE
CHARGE/IN USE indicator
26730
25-Channel Caller ID with Call
Waiting Cordless Telephone
User's Guide
We bring good things to life.
IMPORTANT INFORMATION
NOTICE: The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain telecommunications
network protective, operational and safety requirements. The Industry Canada
does not guarantee the equipment will operate to the users satisfaction.
Before installing this equipment, users should ensure that it is permissible to
be connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection.
The customer should be aware that compliance with the above conditions
may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic water
pipe systems, if present, are connected together. This precaution may be
particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves,
but should contact the appropriate electric inspection authority, or electrician,
as appropriate.
NOTES: This equipment may not be used on coin service provided by the
telephone company.
Party lines are subject to telephone company tariffs and, therefore, you may
not be able to use your own telephone equipment if you are on a party line.
Check with your local telephone company.
INTERFERENCE INFORMATION
This equipment generates and uses radio frequency energy which may
interfere with residential radio and television reception if not properly
installed and used in accordance with instructions contained in this manual.
Reasonable protection against such interference is ensured, although there is
no guarantee this will not occur in a given installation. If interference is
suspected and verified by switching this equipment on and off, the user is
encouraged to try to correct the interference by one or more of the following
measures: Reorient the radio/television receivers antenna, relocate the
equipment with respect to the receiver, plug the equipment and receiver into
separate circuit outlets. The user may also wish to consult a qualified radio/
television technician for additional suggestions. This equipment has been
fully tested and complies with all limits for Class B computing devices
pursuant to part 15 FCC Rules and Regulations. This device complies with
RSS-210 of Industry Canada. Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) This device
must accept any interference, including interference that may cause
undesired operation of the device.
Model 26730D
15575670 (Rev. 1 CAN E)
00-33
Printed in China
1
2
3
ABC DEF
5
4
6
JKL
GHI
MNO
8
7
9
PQRS
WXYZ
TUV
0
TONE
OPER
PHONE
#
TALK
REDIAL
CALL BACK
VOLUME
DELETE
CHANNEL
FORMAT
MEMORY FLASH
OFF
ON
RINGER
CHANNEL
button
FLASH
button
TALK
button
REDIAL
button
TONE
button
RINGER
switch
VOLUME
button
DELETE
button
CALL
BACK
button
FORMAT
button
MEMORY
button
6
5
4
7
ATLINKS Communications Canada, Inc.
(An Alcatel/Thomson Multimedia Joint Venture)
© 2000 ATLINKS Communications Canada, Inc.
Trademark(s) ® Registered
Marque(s) ® déposée(s)
CALLER ID FEATURES
This unit receives and displays information transmitted by
your local phone company. This information can include
the phone number, date, and time;
or
the name, phone
number, date, and time. The unit can store up to 40 calls
for later review.
CALLER ID WITH CALL WAITING
Provided you subscribe to Caller ID with Call Waiting
service from your phone company, you are able to see who
is calling when you hear the call waiting beep. The caller
identification information appears in the display after you
hear the tone.
Press the FLASH button to put the current person on
hold so that you can answer the incoming call.
IMPORTANT: In order to use this feature, you must
subscribe to either the standard Name/Number Caller
ID Service or Caller ID with Call Waiting Service. To
know who is calling while you are on the phone, you
must subscribe to Caller ID with Call Waiting Service.
RECEIVING AND STORING CALLS
When you receive a call, the information is transmitted by
the phone company to your Caller ID telephone between
the first and second ring.
When the memory is full, a new call automatically replaces
the oldest call in memory.
NEW
appears in the display for
calls received that have not been reviewed.
NOTE: Check with your local phone company
regarding name service availability.
REVIEWING MESSAGES
As calls are received and stored, the display is updated to
let you know how many calls have been received.
Press the arrow down (*) button to scroll through the
call records from the most recent to the oldest.
Press the arrow up (#) button to scroll through the call
records from the oldest to the newest.
DELETING RECORDS
Use the DELETE button to erase the record currently
shown in the display or all records.
DELETING THE CURRENT RECORD
1. Make sure the phone is OFF.
2. Press DELETE. The display shows
ERASE CALL ID?
3. Press DELETE again to erase the record.
DELETING ALL RECORDS
1. Make sure the phone is OFF.
2. Press and hold DELETE. The display shows
ERASE ALL?
3. Press DELETE again to erase all records.
Vue de la page 0
1 2

Résumé du contenu

Page 1 - 3175554231

INTRODUCTIONYour Caller ID phone stores and displays specificinformation, provided by your local telephone company, tosubscribers of Caller ID or simi

Page 2 - TELEPHONE

CHANGING A STORED NUMBERUse the same procedure to change a stored number asyou do to store a number—you’re just replacing the phonenumber with a diffe

Commentaires sur ces manuels

Pas de commentaire