Ge 26999 Manuel d'utilisateur télécharger pdf

Plug the power adaptor cord into the power jack on the bottom of

the base and the other end into an electrical outlet. The in use/charge

indicator (on the base) turns on to indicate the battery is charging when

the handset is on the cradle.

Allow the phone to charge for 16 hours prior to ﬁrst use. If you don’t

properly charge the phone, battery performance is compromised.

CAUTION: Use only the ATLINKS USA, Inc. power adaptor

5-2512 (black) or 5-2618 (gray) power adaptor that came with

this unit. Using other power adaptors may damage the unit.

Connecting the Telephone Line

Plug one end of the telephone line cord into the jack on the bottom of

the base called PHONE LINE and the other end into your home’s modular

phone jack. Place the handset in the cradle on the base.

Wall Mounting

If you want to mount the phone on a wall, slip the mounting holes (on the

back of the base) over the wall plate posts, and slide the unit down into

place. (Wall plate not included.)

Handset Layout

Telephone Jack Requirements

To use this phone, you need an RJ11C type modular

telephone jack, which might look like the one pictured

here, installed in your home. If you don’t have a

modular jack, call your local phone company to ﬁnd

out how to get one installed.

Digital Security System

Your cordless phone uses a digital security system to protect against

false ringing, unauthorized access, and charges to your phone line.

When you place the handset in the base, the unit veriﬁes its security

code. After a power outage or battery replacement, you should place the

handset in the base for about 20 seconds to reset the code.

INSTALLATION NOTE: Some cordless telephones operate at

frequencies that may cause or receive interference with nearby

TVs, microwave ovens, and VCRs. To minimize or prevent such

interference, the base of the cordless telephone should not be

placed near or on top of a TV, microwave oven, or VCR. If such

interference continues, move the cordless telephone farther away

from these appliances. Certain other communications devices may

also use the 900 MHz frequency for communication, and, if not

properly set, these devices may interfere with each other and/or

your new telephone. If you are concerned with interference, please

refer to the owner’s manual for these devices on how to properly

set channels to avoid interference. Typical devices that may use the

900 MHz frequency for communication include wireless audio/

video senders, wireless computer networks, multi-handset cordless

telephone systems, and some long-range cordless telephone systems.

Important Installation Information

• Never install telephone wiring during a lightning storm.

• Never install telephone jacks in wet locations unless the jack is

speciﬁcally designed for wet locations.

• Never touch uninsulated telephone wires or terminals, unless the

telephone line has been disconnected at the network interface.

• Use caution when installing or modifying telephone lines.

• Temporarily disconnect any equipment connected to the phone such as

faxes, other phones, or modems.

Installing the Phone

Your cordless telephone/answering system should be placed on a level

surface such as a desk or table top, or you can mount it on a wall.

Installing the Handset Battery

NOTE: You must connect the handset battery before use.

1. Locate battery and battery door which are packaged together inside a

plastic bag and are separate from the handset.

2. Locate the battery compartment on the back of the handset.

3. Plug the battery pack cord into the jack inside the compartment.

NOTE:

It is important to maintain the polarity (black and red

wires) to the jack inside the compartment. To ensure proper battery

installation, the connector is keyed and can be inserted only one way.

Interference Information

This equipment generates and uses radio frequency energy which may

interfere with residential radio and television reception if not properly

installed and used in accordance with instructions contained in this

manual. Reasonable protection against such interference is ensured,

although there is no guarantee this will not occur in a given installation.

If interference is suspected and veriﬁed by switching this equipment on

and off, the user is encouraged to try to correct the interference by one or

more of the following measures: Reorient the radio/television receiver’s

antenna, relocate the equipment with respect to the receiver, plug the

equipment and receiver into separate circuit outlets. The user may also

wish to consult a qualiﬁed radio/television technician for additional

suggestions. This equipment has been fully tested and complies with

all limits for Class B computing devices pursuant to part 15 FCC Rules

and Regulations. This device complies with RSS-210 of Industry Canada.

Operation is subject to the following two conditions: (1) This device may

not cause interference, and (2) This device must accept any interference,

including interference that may cause undesired operation of the device.

Licensing

Licensed under US Patent 6,427,009.

Hearing Aid Compatibility (HAC)

This telephone system meets FCC standards for Hearing Aid

Compatibility.

REN NUMBER IS LOCATED ON THE CABINET BOTTOM

Introduction

CAUTION:

When using telephone equipment, there are basic

safety instructions that should always be followed. Refer to the

IMPORTANT SAFETY INSTRUCTIONS provided with this

product and save them for future reference.

Your cordless telephone/answering system with Caller ID and

Call Waiting is designed to give you ﬂexibility in use and high quality

performance. To get the most from your new cordless telephone/

answering system, we suggest that you take a few minutes right now to

read through this instruction manual. This telephone is a multifunction

product for use with the Call Waiting and Caller ID services available from

your local telephone company. Your Caller ID Call Waiting phone allows

you to:

• View the name and telephone number of a caller (Call Waiting Caller

ID).

• Identify callers before you answer the phone.

• View the time and date of each incoming call.

• Record up to 20 Caller ID messages sequentially.

• Know who called while you are on the other line or when

you were away.

• Screen unwanted calls, eliminate harassment from annoying calls, or

to get prepared before answering a call.

IMPORTANT: In order to use all of the features of this telephone,

you must subscribe to two separate services available from your local

telephone company: the standard Name/Number Caller ID Service

to know who is calling when the phone rings and Caller ID with Call

Waiting Service to know who is calling while you are on the phone.

Because cordless phones operate on electricity, you should have at

least one phone in your home that isn’t cordless, in case the power

in your home goes out.

5. Close the battery compartment by pushing the door up until it snaps

into place.

6. Place the handset in the charging cradle.

Connecting the AC (Electrical) Power

40 Channel 900MHz Call Waiting

Caller ID Cordless Telephone/

Answering System

User’s Guide

26999

Programmable Menus

There are six programmable menus available: Language, Local Area Code,

Ringer Tone, Tone/Pulse, Ringer On/ Off, and Factory Default. When you

program these settings, make sure the phone is OFF (not in talk mode).

Pressing the *tone/exit button will remove you from the menu selection

process without changing the feature you are in.

Display Language

1. Press the ﬂash/program button until 1ENG 2FRA 3ESP shows in the

display.

2. Use the CID/VOL (

or) button or the handset number pad to select 1

(English), 2 (French), or 3 (Spanish). The default setting is “1ENG”.

3. Press the ﬂash/program button to conﬁrm and to advance to the next

menu feature.

Local Area Code

If you enter your local 3-digit area code in the area code menu, your local

area code does not display on the Caller ID (CID) list. Instead, you only

see the local 7-digit number. Calls received from outside your local area

code will display the full 10-digit number.

1. Press the ﬂash/program button until

AREA CODE- - - shows in the

display. The default setting is “- - -”.

2. Use the handset number pad to enter your 3-digit area code.

NOTE: If you make a mistake, press the chan/delete button to

erase the incorrect area code and repeat step 2.

3. Press the ﬂash/program button to conﬁrm and to advance to the next menu

feature.

Ringer Tone

1. Press the ﬂash/program button until RINGER TONE shows in the

display.

2. Use the CID/VOL (

or) button or the handset number pad (1-3) to

enter your selection from Ringer Tone 1, 2, or 3. The default setting is

“RINGER TONE 1”.

3. Press the ﬂash/program button to conﬁrm and to advance to the next menu

feature.

Tone/Pulse

1. Press the ﬂash/program button until 1 TONE 2 PULSE shows in the

display.

2. Use the CID/VOL (





) button or the handset number pad to enter

your selection. The default setting is “1 TONE”.

3. Press the ﬂash/program button to conﬁrm and to advance to the next

menu feature.

Ringer ON/OFF

1. Press the ﬂash/program button until RINGER 1ON 2OFF shows in the

display.

2. Use the CID/VOL (





) button or the handset number pad to enter

your selection. The default setting is “1ON”.

3. Press the ﬂash/program button to conﬁrm and to advance to the next

menu feature.

NOTE: If you turn the ringer OFF, RINGER OFF shows in the

handset display.

Factory Default

This feature allows you to restore the unit’s original features.

1. Press the ﬂash/program button until DEFAULT shows in the display.

2. Use the CID/VOL (





) button to scroll to YES. The default setting is

“NO”.

3. Press ﬂash/program to conﬁrm. You will hear a conﬁrmation tone.

Cordless Phone Basics

Making a Call

1. Press the TALK/CALL BACK button and dial the desired number.

-OR-

To perform preview dial, dial the number ﬁrst then press the TALK/

CALL BACK button.

2. To hang up, press the TALK/CALL BACK button or place the handset in

the base cradle.

IMPORTANT: Because cordless phones operate on electricity, you

should have at least one phone in your home that isn’t cordless, in

case the power in your home goes out.

Redial

Press the redial button to quickly dial the last number you called (up to 32

digits).

If you get a busy signal, and want to keep dialing the number, press

redial to dial the number again.

Receiving a Call

1. To answer a call press the TALK/CALL BACK button on the handset

before you begin speaking.

2. To hang up, press the TALK/CALL BACK button or place the handset in

the base cradle.

In Use Indicator

When the in use/charge indicator on the base is lit, the handset is either

in use or charging. The in use/charge indicator on the base ﬂashes when

you receive a call.

Flash

If you subscribe to the combined Call Waiting Caller ID service from

your local telephone company you will receive Caller ID information (if

available) on Call Waiting calls. During a phone call, you will hear a beep

to indicate another call is waiting on the line and Caller ID information

for the waiting call shows on the handset display. To connect the waiting

call, press the ﬂash/program button on the handset and your original call

is put on hold. You may switch back and forth between the two calls by

pressing the ﬂash/program button.

TIP: Do not use the TALK/CALL BACK button to activate custom

calling services such as call waiting, or you’ll hang up the phone.

Volume

When the phone is ON, press the CID/VOL (or) on the handset to

adjust the volume of the handset’s earpiece. There are four settings. Press

the right arrow to increase the volume and left arrow to decrease the

volume. You will see the volume setting on the handset display. VOL 4 is

the maximum and VOL 1 is the minimum.

Channel Button

While talking on the phone, you might need to manually change the

channel in order to reduce static caused by appliances, such as baby

monitors, garage door openers, microwave ovens, or other cordless

phones. Press and release the chan/delete button to move to the next

clear channel.

Temporary Tone

This feature is useful only if you have pulse (rotary) service. Temporary

Tone Dialing enables pulse (rotary) service phone users to access

touchtone services offered by banks, credit card companies, etc. For

example, when you call your bank you may need to enter your bank

account number. Temporarily switching to touchtone mode allows you to

send your number.

1. Dial the telephone number and wait for the line to connect.

2. When your call is answered, press the *tone/exit button on the handset

to temporarily change from pulse dialing to tone dialing.

3. Follow the automated instructions to get the information you need.

4. Hang up the handset and the phone automatically returns to pulse

(rotary) dialing mode.

Exit

Press the *tone/exit button to cancel any command you initiated.

Paging the Handset

This feature helps to locate a misplaced handset.

Press the page button on the base. The handset will beep for about two

minutes or until you press TALK/CALL BACK on the handset or press the

page button on the base.

NOTE: You can still page the handset if the ringer is turned off. If

the battery is dead, the Paging feature will not work.

Caller ID Features

Caller ID (CID) is a service available from your local telephone company.

For Caller ID to work on this system, you must subscribe to Caller ID

service. To receive Caller ID information for a Call Waiting call, you must

subscribe to the combined Caller ID Call Waiting service. The unit can

store up to 20 calls for later review.

When your telephone rings, and you are subscribed to Caller ID Call

Waiting service, you will receive information (if available) transmitted by

your local telephone company. You will also receive Caller ID information

from Call Waiting calls. If you receive an incoming call and you are

already on the phone, a beep indicates the presence of a Call Waiting Call

on the line, and Caller ID information for the Call Waiting call shows on

the display. This information may include the phone number, date and

time; or the name, phone number, and date and time.

Receiving and Storing Calls

When you receive a call, the information is transmitted by the phone

company to your Caller ID telephone between the ﬁrst and second ring.

VERY IMPORTANT: The Caller ID feature of this product requires

a subscription to Caller ID service from your telephone company.

When the phone’s memory is full, a new call automatically replaces the

oldest call in memory.

NEW appears in the display for calls received that

have not been reviewed.

NOTE: Check with your local phone company regarding name

service availability.

Reviewing Caller ID Records

As calls are received and stored, the display is updated to let you know

how many calls have been received.

• Make sure the phone is

OFF (not in TALK mode).

• Press the CID/VOL (

) button to scroll through the call records from the

most recent to the oldest.

• Press the CID/VOL (

) button to scroll through the call records from the

oldest to the newest.

Deleting the Current Record

1. When the Caller ID record shows in the display, press and release the

chan/delete button. The display shows

DELETE CALL ID?

2. Press chan/delete button again to conﬁrm. You will hear a conﬁrmation

tone, the display shows DELETED, then the next Caller ID record

appears in the display.

Deleting All Records

Press the

CID/VOL (or)

button until a Caller ID record is displayed

2. Press and hold chan/delete until unit beeps. The display shows

DELETE

ALL?

3. Press chan/delete again to erase all records. You will hear a

conﬁrmation tone, and the display shows

NO CALLS.

Storing Caller ID Records in Memory

NOTE: Caller ID record should be in correct format for dialing as

record cannot be changed once it is stored in memory location.

1. Press the CID/VOL (or) button until the desired Caller ID record is

displayed.

2. Press the memory button.

3. Press a number (0-9) to store the dialed number in that memory

location. You will hear a conﬁrmation tone. Example, press the

number 1 key to store the record in memory location 1.

To Replace an Old Memory with a New Caller ID

Record:

1. Repeat steps 1 through 3 in Transferring Caller ID Records to Memory.

After entering the memory location, REPLACE MEMO?

shows in the

display.

2. Press the memory button again, and the new Caller ID record replaces

the old memory in that location. You will hear a conﬁrmation tone.

Dialing a Caller ID Number

1. Make sure the phone is OFF (not in TALK mode).

2. Use the CID/VOL (

or) button to display the desired Caller ID record.

3. Press the TALK/CALL BACK button to dial the number.

Changing the Number Format

The format/answerer button lets you change the format of the displayed

number. The available formats are as follows.

7-digit 7-digit telephone number.

10-digit 3-digit area code + 7-digit telephone number.

11-digit long distance code “1” + 3-digit area code + 7-digit telephone

number.

1. Use the CID/VOL (

or) button to scroll to the number you want to

call back.

2. If the number does not dial as shown, press the format/answerer

button. Repeat if necessary, until the correct number of digits shows in

the display.

3. Press the TALK/CALL BACK button.

Important Information

NOTICE: This product meets the applicable Industry Canada

technical speciﬁcations.

The equipment must be installed using an acceptable method of

connection. The customer should be aware that compliance with the

above conditions may not prevent degradation of service in some

situations.

Repairs to certiﬁed equipment should be made by an authorized

Canadian maintenance facility designated by the supplier. Any repairs

or alterations made by the user to this equipment, or equipment

malfunctions, may give the telecommunications company cause to

request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground

connections of the power utility, telephone lines and internal metallic

water pipe systems, if present, are connected together. This precaution

may be particularly important in rural areas.

CAUTION: Users should not attempt to make such connections

themselves, but should contact the appropriate electric inspection

authority, or electrician, as appropriate.

NOTES: This equipment may not be used on coin service provided by the

telephone company.

Model 26999GF

00006816 (Rev. 0 CAN E)

05-32

Printed in China

4. Insert the battery pack.

Memory

Store up to ten 24-digit numbers in memory for quick dialing. This

memory feature is in addition to the 20 Caller ID records that can be

stored in memory.

Storing a Name and Number in Memory

1. Make sure the phone is OFF (not in TALK mode).

2. Press the memory button.

3. Press a number (0-9) to store the dialed number in that memory

location. Or use the CID/VOL (

or) to scroll to desired location. If the

memory location is occupied, the memory location and stored name

and number appear on the screen.

NOTE: If the memory location is empty, “EMPTY” appears in the

display.

4. Press the memory button again. The display shows ENTER NAME.

NOTE: If you don’t want to enter the name, skip step 5.

5. Use the handset number keypad to enter a name (up to 15 characters).

More than one letter is stored in each of the number keys. For

example, to enter Bill Smith, press the 2 key twice for the letter B.

Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the

letter L, and wait for 1 second. Press the 5 key 3 times for the second

letter L, and press the 1 key to insert a space between the ﬁrst and last

name. Press the 7 key 4 times for the letter S; press the 6 key once for

the letter M; press the 4 key 3 times for the letter I; press the 8 key for

the letter T; press the 4 key twice for the letter H.

NOTE: If you make a mistake press the chan/delete button to

backspace and erase the wrong character(s) or number(s).

6. Press the memory button again to save the name. The display shows

ENTER TEL NUMBR

7. Use the handset number keypad to enter the telephone number (up

to 24 digits, including pauses) and press the memory button again to

save the number. The unit beeps to conﬁrm.

8. To enter another name and number in a different memory location,

return to step 1 and repeat the process.

Storing a Redial Number

1. Repeat steps 1 through 6 in Storing a Name and Number in Memory.

2. Press the redial button.

3. Press the memory button to store the number. You will hear a

conﬁrmation tone.

To Replace an Old Memory with a New Redial Number

1. Repeat steps 1 through 6 in Storing a Name and Number in Memory.

2. Press the redial button.

3. Press the memory button, and REPLACE MEMO? shows in the display.

4. Press the memory button to replace the old memory with the new

redial number. You will hear a conﬁrmation tone.

Changing a Stored Number

1. Repeat steps 1 through 7 in Storing a Name and Number in Memory.

REPLACE MEMO? shows in the display.

2. Press the memory button to store the number. You will hear a

conﬁrmation tone.

Dialing a Stored Number

1. Make sure the phone is ON by pressing the TALK/CALL BACK button.

2. Press the memory button.

3. Press the number (0-9) for the desired memory location. The number

dials automatically.

1. Make sure the phone is

OFF (not in TALK mode).

2. Press the memory button.

3. Press the memory location for the phone number you want to dial, or

use the CID/VOL (

or) button to scroll through the numbers stored

in memory until the desired number is shown.

4. Press TALK/CALL BACK. The number dials automatically.

Chain Dialing from Memory

Use this feature to make calls which require a sequence of numbers,

such as using a calling card for a frequently called long distance number.

You simply dial each part of the number sequence from memory. The

following example shows how you can use chain dialing to make a call

through a long distance service:

RED WIRE

BLACK WIRE

BATTERY

PRESS DOWN

FIRMLY

Modular

telephone

line jack

Wall plate

Before You Begin

Parts Checklist

Make sure your package includes the items shown here.

Telephone Setup

ATLINKS Communications Canada Inc.

Trademark(s) ® Registered

Marque(s) ® déposée(s)

Base

Handset

Line cord

power

adaptor

Handset battery

format/answerer

(button)

CID/VOL





(button)

redial

(button)

TALK/CALL

BACK (button)

ﬂash/program

(button)

*tone/exit

(button)

chan/delete

(channel/

delete button)

memory (button)

#pause (button)

display

review



(button)

skip



(button)

play/stop

(button)

erase (button)

volume





(button)

page (button)

memo (button)

PLAY/STOP



(button)

display

review/skip





(button)

microphone

answer on/off button

announce button

hour (button)

day/check (button)

min (button)

in use/charge

(indicator)

Time

Date

Number of

Calls

Caller ID

name

Caller ID

phone number

1 2

Résumé du contenu

Page 1 - PRESS DOWN

Plug the power adaptor cord into the power jack on the bottom of the base and the other end into an electrical outlet. The in use/charge indicator (on

Page 2 - button again

The Number For Memory Location Long distance access number 7 Authorization code 8 Frequently called long distance number 91. Make sure the ph

Commentaires sur ces manuels

Pas de commentaire

Ge 26999 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Téléphone sans fil à combiné Ge 26999. GE 26999 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Téléphone sans fil à combiné Ge 26999