GE Fanuc Automation Programmable Control Products Series 90™-30 PROFIBUS Slave Module User's Manual GFK-2193A August 2004
GFK-2193A 2-1 Installation This chapter contains information on the following procedures: Reviewing system power requirements Instal
2-2 Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004 GFK-2193A 2 Connecting the Slave to the PROFIBUS Network Network Se
GFK-2193A Chapter 2 Installation 2-3 2 PROFIBUS Cable Types The recommended cable is Belden 3079A PROFIBUS Cable This is a shielded, 150
2-4 Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004 GFK-2193A 2 Note: For proper network termination, it is essential
GFK-2193A 3-1 Configuration These configuration procedures are intended for users with at least a basic knowledge of the CIMPLICITY Machin
3-2 Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004 GFK-2193A 3 Configuring a PROFIBUS Slave Module The PROFIBUS Slave
GFK-2193A Chapter 3 Configuration 3-3 3 Input Data Area Tab The input data area describes data received over the network by the Slave module f
3-4 Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004 GFK-2193A 3 Output Data Area Tab The output data area describes dat
GFK-2193A 4-1 Status and Diagnostics The following methods can be used to obtain status and diagnostic data: Observing and interpreting
4-2 Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004 GFK-2193A 4 Status/Firmware ID Array The starting reference address
GFL-002 Warnings, Cautions, and Notes as Used in this Publication Warning Warning notices are used in this publication to emphasize that hazardous
GFK-2193A Chapter 4 Status and Diagnostics 4-3 4 Enable Input Command Block PointerRack/Slot Location Task #Fault OutputCOMM_REQIN FTSY
4-4 Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004 GFK-2193A 4 FT Output: The function’s FT (fault) output can provide
GFK-2193A Chapter 4 Status and Diagnostics 4-5 4 COMMREQ Programming Requirements and Recommendations COMMREQ instructions should be enable
4-6 Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004 GFK-2193A 4 COMMREQ Status Word The following table defines the for
GFK-2193A Chapter 4 Status and Diagnostics 4-7 4 PROFIBUS Slave Module COMMREQ Reference The PROFIBUS Slave module supports the following COMM
4-8 Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004 GFK-2193A 4 (Word 7) Command Code: Word 7 specifies the Command co
GFK-2193A Chapter 4 Status and Diagnostics 4-9 4 Network Parameter Errors The following errors codes may be returned in bits 0—6 in the Get Sl
4-10 Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004 GFK-2193A 4 Read Module Header (5) The Read Module Header command
GFK-2193A Chapter 4 Status and Diagnostics 4-11 4 (Word 9) Local PLC - Memory Starting Address: Word 9 determines the starting address in the
4-12 Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004 GFK-2193A 4 Clear Counters (6) The Clear Counters Command sets the
Contents GFK-2193A iii Overview and Specifications... 1-1
Index GFK-2193A Index-1 C Clear Counters (6), 4-12 COMMREQs Clear Counters (6), 4-12 Get Slave Status details, 4-7 memory types, 4-7 PROFIBUS M
Contents iv Series 90™-30 PROFIBUS Slave Module User's Manual –August 2004 GFK-2193A Get Slave Status Command Block – Basic Example ...
GFK-2121A 1-1 Overview and Specifications This manual provides instructions for installing, programming, and troubleshooting control syste
1-2 Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004 GFK-2121A 1 SYS COM PROFIBUS DP SLAVE 5-IGND SERVICE RS232 PROFIBU
GFK-2121A Chapter 1 Overview and Specifications 1-3 1 PROFIBUS Basics PROFIBUS Network Overview • PROFIBUS is an open, vendor independent Fiel
1-4 Series 90™-30 PROFIBUS Slave Module User's Manual – August 2004 GFK-2121A 1 Data bandwidth Demands on PROFIBUS Communications Syste
GFK-2121A Chapter 1 Overview and Specifications 1-5 1 Figure 1-2. Repeaters and bus termination Network Connectors PROFIB
Commentaires sur ces manuels