GE PT9800SHSS Manuel d'instructions télécharger pdf

2 C

CUTOUT FOR DOUBLE OVENS

(2 THERMAL OVENS)

NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim

both sides equally to establish the cutout width.

Dim. Description 27” Double Oven 30” Double Oven with

Pedestal

30” Double Oven

without Pedestal

A Cabinet Width 27” (68.6 cm) 30” (76.2 cm) 30” (76.2 cm)

B Cutout Width 25” (63.5 cm) min.

ø4” (64.1 cm) max.

ø2” (72.4 cm) min.

ø8” (72.7 cm) max.

ø2” (72.4 cm) min.

ø8” (72.7 cm) max.

C Cutout Height

ø16” (126.2 cm) min.

ø8” (127.3 cm) max.

ø16” (131.6 cm) min.

ø16” (131.9 cm) max.

50 ¼” (127.64cm)

D Overlap of Oven

Over Side Edges

of Cutout

1” (2.5 cm)

ø16” (1.75 cm)

Clearance to

Adjacent Corners,

Drawers, Walls, etc.,

When Door Is Open

23” (58.4 cm) min. 23” (58.4 cm) min. 23” (58.4 cm) min.

F Overlap of Oven

Top of Cutout

1” (2.5 cm) min. 1” (2.5 cm) min.

” (3.2 cm) for PT9550)

1” (2.5 cm) min.

” (3.2 cm) for PT9550)

G Overlap of Oven

Bottom of Cutout

1” (2.5 cm) min. 1

ø4” (3.2 cm) 1

ø4” (3.2 cm)

H Junction Box

Location

ø4” (22.2 cm) max.

right side only

ø2” (24.1 cm) max.

right side only

ø2” (24.1 cm) max.

right side only

J Height to Bottom

of Junction Box

44” (111.8 cm) 47” (119.4 cm) 47” (119.4 cm)

K Recommended

Cutout Location

from Floor

ø4” (33.7 cm) 12” (30.5 cm) 12” (30.5 cm)

2 A

CUTOUT FOR SINGLE OVENS IN WALL CABINET

NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim

both sides equally to establish the cutout width.

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

•

,03257$17³ Save these instructions

for local inspector’s use.

•

,03257$17³ Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• Skill level – Installation of this appliance

requires a qualified installer or electrician.

• Proper installation is the responsibility

of the installer.

• Product failure due to improper installation

is not covered under Warranty.

• Product is for indoor use only.

Installation Instructions

27” & 30” Electric Built-In Wall Ovens

FOR YOUR SAFETY:

WARNING

Before beginning the installation, switch power off at the service panel and

lock the service disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.

Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,

stand or hang on the oven door.

Make sure the wall coverings, counters and cabinets around the oven can withstand the heat

(up to 200°F [93.3°C]) generated by the oven.

Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

MATERIALS YOU MAY NEED

Junction Box

Wire Nuts

Strain Relief Clamp for 1/2” Conduit

36” (91 cm) of String

TOOLS YOU MAY NEED

1/8” Drill Bit and Electric or Hand Drill

Phillips Screwdriver

Wire Strippers

7/16” Nut Driver

T20 Screwdriver (hinge bracket)

1/4” Nut Driver

REMOVE PACKAGING MATERIALS

Failure to remove packaging materials could result in damage to the appliance. Remove all packing

parts from oven, racks and heating elements. Remove protective film and labels on the outer door

and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping

screws securing the oven to the base pad. Open oven door and remove literature pack and oven

racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation

process. The trim is wrapped separately and taped to the top of the unit. Remove pedestal rails from

seperate box and set aside (30” Double Wall Ovens Only).

PREPARE THE OPENING

NOTE: If the cabinet does not have a solid bottom, two

braces or runners must be installed to support the weight

of the oven. For single ovens, the runners and braces

must support 200 lbs (91 kg). For double ovens, the

runners and braces must support 375 lbs. (170 kg).

NOTE: If marks, blemishes or the cutout opening are

visible above the installed oven, it may be necessary to

add wood shims under the runners and front trim until

the marks or opening are covered.

NOTE: If the cabinet does not have a front frame and

the sides are less than ¾” (1.9 cm) thick, shim both sides

equally to establish the cutout width.

ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired) into an

approved junction box. A plug and receptacle is NOT permitted on these products.

These ovens

are not

approved for

stackable

installations.

Cutout –

observe all

dimensions and

requirements.

Cutout –

observe all

dimensions and

requirements.

2” (5.1 cm) Min.

30.5” (77.5 cm)

30” models

27” (68.58 cm)

27” models

Center Line Center Line

Side-by-Side Installations

Install two ovens in separate cutouts.

Dimension Dimension Description 27” Single Oven 30” Single Oven

A Cabinet Width 27” (68.6 cm) 30” (76.2 cm)

B Cutout Width 25” (63.5 cm) min. 28

ø2” (72.4 cm) min.

ø4” (64.1 cm) max. 28

ø8” (72.7 cm) max.

C Cutout Height 27

ø8” (70.2 cm) min. 27

ø4” (69.2 cm) min.

ø8” (71.4 cm) max. 27

ø16” (69.4 cm) max.

D Overlap of Oven Over 1” (2.5 cm)

ø16” (1.75 cm)

Side Edges of Cutout

E Clearance to 23” (58.4 cm) min. 23” (58.4 cm) min.

Adjacent Corners,

Drawers, Walls, etc.,

When Door Is Open

F Overlap of Oven 1” (2.5 cm) min. 1” (2.5 cm) min.

Top of Cutout (1

ø4” (3.2 cm) for PT9050)

G Overlap of Oven 1” (2.5 cm) min. 1

ø4” (3.2 cm)

Bottom of Cutout

H Junction Box Location 8

ø4” (22.2 cm) max. 9

ø2” (24.1 cm) max.

right side only right side only

Suitable

Bracing

to Su

ort

2" x 4" (5 cm x 10 cm)

or Equivalent Runners Level

with Bottom of Cutout

and Flush with Sides of Cutout

2 B

CUTOUT FOR SINGLE OVENS – UNDER COUNTER

NOTE: These ovens are only approved to be installed under the specific models as labeled on the unit.

Dimension Dimension Description 27” Single Oven 30” Single Oven

A Cabinet Width 25” (63.5 cm) min. 28

ø2” (72.4 cm) min.

ø4” (64.1 cm) max. 28

ø8” (72.7 cm) max.

B Cutout Height 27

ø8” (70.2 cm) min. 27

ø4” (69.2 cm) min.

ø8” (71.4 cm) max. 27

ø16” (69.4 cm) max.

C Unit Overlap Top 1” (2.5 cm) 1” (2.5 cm)

ø4” (3.2 cm) for PT9050)

D Unit Overlap Bottom 1” (2.5 cm) 1

ø4” (3.2 cm)

E Unit Overlap Side Edges 1” (2.5 cm)

ø16” (1.75 cm)

F Junction Box Location 8

ø4” (22.2 cm) max. 9

ø2” (24.1 cm) max.

right side only right side only

Continue to Section 4.

NOTE: One cooktop may be centered over either oven in

the side-by-side installation.

Cutout – observe

all dimensions and

requirements.

2” (5.1 cm) Min.

30.5” (77.5 cm) 30” models

27” (68.58 cm) 27” models

Center Line Center Line

Side-by-Side Installations

Install two ovens in separate cutouts.

Cooktop

Cutout – observe

all dimensions and

requirements.

2 F

CUTOUT FOR INSTALLATION OVER A WARMING DRAWER

NOTE: Install the oven only with specific models listed on the label located on top of the oven.

NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports

above the Warming Drawer location do not obstruct the required interior depth and height.

When installing a Warming Drawer below a single or double oven, a separate 120V, 60 HZ, properly

grounded receptacle must be installed. Refer to installation instructions packed with

the Warming Drawer for specific installation requirements.

2 E

SECURING UPPER MICROWAVE/ADVANTIUM OVEN TO CABINET

For double oven with microwave or Advantium upper ovens. Secure a wooden cleat to side of cabinet

so that the upper oven can be secured to the cleat with provided screws

27” Cabinet requirements

• No shims (or cleats) required when cabinet is in minimum

width condition.

• If cabinet is at maximum width condition, add wood

shims to bring cabinet to minimum condition.

30” Cabinet requirements

• No shims (or cleats) required when cabinet is in minimum

width condition.

• If cabinet is at maximum width condition, fix the wood

cleats as shown in illustration.

2 D

CUTOUT FOR DOUBLE OVENS (with Upper Microwave Oven)

NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim

both sides equally to establish the cutout width.

Anti-Tip Block Against

Rear Wall Per Warming

Drawer Requirement

2" (5.1 cm)

Min.

Per Warming

Drawer

Requirement

Continue to Section 3 for DWO with Pedestal. Otherwise, continue to Section 4.

DESIGN INFORMATION

SINGLE OVEN INSTALLATIONS

The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also

be installed below a countertop or below specified cooktops. See the label on top of the oven for approved

models.

DOUBLE OVEN INSTALLATIONS

A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of the

oven for approved models.

IMPORTANT: Always refer to individual installation instructions packed with each product for specific

requirements.

Continue to Section 4

Continue to Section 4.

Junction

Box

Location

(junction

box may

be located

in adjacent

cabinet)

22” (55.9

cm) Min. to

Bottom of

Junction

Box

Cutout Depth

23-1/2”

(59.7 cm) Min.

Recommended

Cutout Location

from Floor

32-1/2” (82.6 cm)

Opening

Between Inside

Walls Must be

at Least 28-1/2”

(72.4 cm) Wide

Junction

Box

Location

(junction

box may

be located

in adjacent

cabinet)

Cutout Depth

23-1/2”

(59.7 cm) Min.

Note: Allow

1/4” (0.64 cm)

clearances

from side

edges of oven

door.

PEDESTAL RAIL INSTALLATION (30” DOUBLE OVENS ONLY)

A. Place one pedestal rail on each cabinet runner or centered on opposite side of solid cabinet bottom

flush with side of cabinet opening. Locate each rail so that front of rail is behind front cabinet

opening.

B. Drill pilot holes and attach rails to runner or bottom of cabinet with provided hardware.

Dim. Description 27” Oven

with Microwave

30” Oven

with Microwave

A Cabinet Width 27” (68.6 cm) 30” (76.2 cm)

B Cutout Width 25” (63.5 cm) min.

ø4” (64.1 cm) max.

ø2” (72.4 cm) min.

ø8” (72.7 cm) max.

C Cutout Height

ø8” (104.5 cm) min.

ø4” (104.8 cm) max.

ø16” (107.2 cm) min.

ø4” (107.3 cm) max.

D Overlap of Oven Over Side Edges

of Cutout

1” (2.5 cm)

ø16” (1.75 cm)

E Clearance to Adjacent Corners,

Drawers, Walls, etc., When Door

Is Open

23” (58.4 cm) min. 23” (58.4 cm)

F Overlap of Oven Top of Cutout 1” (2.5 cm) min. 1” (2.5 cm) min.

G Overlap of Oven Bottom of Cutout 1” (2.5 cm) min. 1

ø4” (3.2 cm)

H Junction Box Location 8

ø4” (22.2 cm) max.

right side only

ø2” (24.1 cm) max.

right side only

6.375”

27.5”

1.5”

3.0”

Cleat locations on 30” cabinet

with maximum cutout condition

Wood Cleats

4 A

DOOR REMOVAL (RECOMMENDED)

NOTE: Door removal is not a requirement for installation of the product but is an added convenience.

To remove the door:

A. Open the oven door as far as it will go.

B. Remove hinge bracket from front frame and set aside. The hinge bracket must

be replaced for proper door functionality when door is reinstalled.

C. Push both hinge locks down toward the door frame to the unlocked position.

This may require a flat-blade screwdriver. DO NOT LIFT THE DOOR BY THE

HANDLE!

D. Place hands on both sides of the door and close the oven door to the removal

position (approximately 1”–2” [2.5 cm–5.1 cm] from the closed position).

E. Lift the door up and out until the hinge arms clear the slots.

NOTE: The oven door is very heavy. Be sure

you have a firm grip before lifting the oven door off the hinges. Use caution

once the door is removed. Do not lay the door on its handle.

This could cause dents or scratches.

Hinge Slot

Hinge Arm

Hinge Unlocked Position

Hinge Clears Slot

Hinge Bracket

31-10965-1

03-14 GE

1 2 3 4

Résumé du contenu

Page 1 - Installation Instructions

2 CCUTOUT FOR DOUBLE OVENS (2 THERMAL OVENS)NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim both

Page 2 - DWO’s with pedestals

5 ELECTRICAL REQUIREMENTSWARNING:This appliance must be properly grounded.WARNING: To prevent fire or shock, do not use an extension cord with this a

Page 3 - Instrucciones de instalación

2 B ABERTURA PARA HORNOS ÚNICOS – BAJO EL MOSTRADOR DE ENCIMERANOTA: Estos hornos sólo pueden instalarse bajo los modelos específicos como se indica

Page 4 - DWO sin pedestales

5 REQUISITOS ELÉCTRICOSADVERTENCIA: Este aparato debe contar con una adecuada conexión a tierra. ADVERTENCIA:Para prevenir un incendio o descarga elé

Commentaires sur ces manuels

Pas de commentaire

GE PT9800SHSS Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Fours GE PT9800SHSS. GE PT9800SHSS Instructions / Assembly Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Fours GE PT9800SHSS