Ge 00000737 Manuel d'utilisateur télécharger pdf

• With the rounded end of the pedestal pointing upward,

insert the tab on the end of the pedestal into the middle slot

on the bottom of the base, then push the pedestal down

until the two tabs on the left and right corners of the

pedestal snap (lock) into the two lower slots on the bottom

of the base.

• Slip the mounting holes over the wall plate posts and

firmly slide the unit down into place (wall plate not

included).

SETTING UP THE CALLER ID MENU

You should not plug the telephone into the modular jack while setting up the Caller ID menu.

1. Press the MENU button to enter the menu feature configuration mode.

# 1. >ENG FRA ESP (CID language default English)

# 2. CONTRAST (default level is 3).

# 3. LOCAL AREA CODE

# 4. TONE/PULSE (Default is tone dialing).

2. Press the MENU button to scroll through the 4 menu screens.

3. Use the  or  buttons to select the desired setting.

NOTE: You have 20 seconds following an entry before the phone returns to the Summary Screen.

DISPLAY LANGUAGE

This adjustment allows you to display the Caller ID prompts in English, French, or Spanish.

1. Press the MENU button until

ENG FRA ESP

shows in the display.

2. Use the  or  buttons to select

ENG, FRA or ESP.

3. Press the MENU button again to save.

CONTRAST

This adjustment allows you to adjust the contrast of the display.

1. Press the MENU button until

CONTRAST

shows in the display.

2. Use the  or  buttons to select level 1, 2, 3, 4, or 5.

3. Press the MENU button again to save.

LOCAL AREA CODE

The telephone uses the programmed area codes to determine the number format to display

when a valid Caller ID signal is received. Numbers that match the local area code are

displayed as seven digits and are used for dialing back previous numbers. Entering your local

area code will also help you immediately know if the call is local or long distance when viewing

the CID records in the display.

NOTE: If you make a mistake and want to start over again, press the DELETE button to erase

all of the digits.

1. Press the MENU button until

LOCAL AREA CODE

shows in the display.

2. Press the  button to select digit.

3. Press the  button to enter the second and third digit.

4. Press the MENU button to save.

DIALING MODE

This adjustment allows you to select tone (touch-tone) or pulse (rotary) dialing.

1. Press the MENU button until

TONE/PULSE MODE

shows in the display.

2. Press the  or  buttons to show the current dialing mode. The default is

TONE

dialing.

3. To change the dialing mode, press the  or  buttons. The display alternates between the

two modes.

4. Press the MENU button again to save.

NOTE: The phone will exit Set Up after 20 seconds if no buttons are pressed.

REMINDER: The time and date are programmed automatically when the first Caller ID record

is successfully received after set up.

CALLER ID (CID) FEATURES

CID SUMMARY SCREEN

The Summary Screen shows the current time, date, and number of new calls to review. It is

displayed until any button is pressed.

NOTE: The number of new calls is displayed until all new calls have been reviewed.

RECEIVING AND STORING CID CALLS

This unit receives and displays information transmitted by your local phone company. This

information can include the phone number, date, and time; or the name, phone number, date,

and time. The unit can store up to 75 calls for later review. When the memory is full, a new call

automatically replaces the oldest call in memory.

NEW

appears in the display for calls received

that have not been reviewed.

REVIEWING CID RECORDS

• Press the  or  buttons to view the call records.

• Press the  button to scroll through the call records from the most recent to the oldest.

• Press the  button to scroll through the call records from the oldest to the newest.

• When all of the records have been viewed,

START/END

appears in the display.

DELETING CID RECORDS

• To delete the record shown in the display, press the DELETE button once.

• To delete all records while reviewing, press and hold the DELETE button for about three

seconds.

DELETE ALL?

appears in the display. Press DELETE again to complete.

DIALING BACK

When reviewing Caller ID records, you can dialback the numbers on the display by pressing

the DIAL button.

NOTE: If PICKUP PHONE shows in the display, no other changes to the number can be made.

The information sent from the telephone company is known to be a valid number for dialing

back (used only in very limited areas). Once you pickup the phone, the number is

automatically dialed.

IF YOU PROGRAMMED YOUR LOCAL AREA CODE

1. Use the  or  buttons to display the number you want to dial.

2. Press the DIAL button.

• If you see a number with seven digits (i.e. 555-1234), then the call is from within your area

code. However, this does not guarantee the call is a local call.

• If you see a number with 11 digits (i.e. 1-234-555-1234), then the call is not from within your

area code.

NOTE: A timer (10 seconds on-hook and 3 seconds off-hook) located in the upper right side of

the display will start, letting you know how much time is left until the unit returns to the

Summary Screen.

3. If you are at on-hook and

PICKUP OR ADJ

displays, you can adjust the phone number

format by pressing the DIAL button. If the phone is off-hook and

ADJUST

shows in the

display, you can adjust the phone number format by pressing the DIAL button. For example,

sometimes a 7-digit local number cannot be dialed because it requires a 10-digit or 11-digit

format. Press the DIAL button repeatedly to scroll through the 7, 10, and 11-digit numbers.

7-digits: 7-digit telephone number (i.e. 555-5555)

10-digits: 3-digit area code + 7-digit telephone number (i.e. 425-555-5555)

11-digits: long distance code 1 + 3-digit area code + 7-digit telephone number

(i.e. 1-425-555-5555)

4. To dial the displayed number, and the phone is on-hook, pick up the handset or press the

SPEAKER button before the timer reaches 0. If the phone is off-hook, wait until the time

reaches 0.

NOW DIALING

shows in the display and the number is dialed.

IF YOU DID NOT PROGRAM YOUR LOCAL AREA CODE

1. Use th  or  buttons to display the number you want to dial. You will only see 10-digit

numbers (i.e. 234- 555-1234).

2. See steps 2 through 4 in the previous section to complete the dialback process.

LOCATION

Your phone features a speakerphone for ease of use and convenience during a phone

conversation. At any time during a conversation, you can lift the handset to stop using the

speakerphone. Likewise, when you are using the handset, press the SPEAKER button and place

the handset in the cradle to switch to the speakerphone.

For best speakerphone performance, avoid the following:

• Areas with high background noise. (The microphone might pick up these sounds and

prevent the speakerphone from going into the receiving mode when you finish talking.)

• Surfaces affected by vibration.

• Recessed areas such as in a corner, under a cupboard, or next to a cabinet, which can

generate an echo effect.

SPEAKERPHONE USE

Note the following guidelines when using the speakerphone:

• The speakerphone works similar to a two-way radio in that you can only listen or talk at

one time.

• Stay reasonably close to the phone so that you can be clearly heard by the person to whom

you are talking.

• You can adjust the speaker volume by pressing the volume button continuously or pressing

the review button

after pressing the volume button.

• The speakerphone indicator light comes on when the speakerphone is in use.

NOTE: Batteries must be installed for the speakerphone to operate.

TELEPHONE BASICS

You can use the telephone by speaking into and listening through the handset, or by using the

speakerphone.

RECEIVING A PHONE CALL

1. Lift the handset or press SPEAKER to answer the call.

2. Replace the handset in the cradle or press the SPEAKER button to hang up.

MAKING A PHONE CALL

1. Lift the handset or press the SPEAKER button. Wait for a dial tone.

2. Dial the telephone number you want to call.

3. Replace the handset in the cradle, or press the SPEAKER button to hang up.

VOLUME

You may adjust the handset and speakerphone volume independently with the VOL button or

the  or  buttons. Both handset receiver volume level and speakerphone volume level are

saved in memory.

ADJUSTING THE HANDSET RECEIVER VOLUME

While using the handset, you can adjust the speaker volume by pressing the VOL button

continuously or pressing the  or  buttons after pressing the VOL button. REC (Handset

Receiver) volume shows in the display.

ADJUSTING THE SPEAKERPHONE VOLUME

While using the speakerphone, you can adjust the speaker volume by pressing the VOL button

continuously or pressing the  or  buttons after pressing the VOL button. SPK volume level

shows in the display.

NOTE: Both handset receiver and speakerphone volume return to the default setting (low) if

the unit is power up reset.

REDIAL

You may redial the last number you called by pressing the REDIAL button after you hear a

dial tone.

NOTE: The redial feature holds the last number (up to 32 digits) that you dialed in memory. If

you pressed any other numbers after dialing the phone number (for example, when accessing a

voice-menu system) then those numbers are also dialed.

MUTE

Use the MUTE button to interrupt a phone conversation to talk privately with someone else in

the room. A conversation can be muted while using the speakerphone or handset.

1. Press the MUTE button. The mute indicator illuminates.

2. Press MUTE again to turn it off.

NOTE: Switching from speakerphone to handset cancels mute.

FLASH

Press FLASH to activate special features of your telephone network, such as call transfer, or

special services from your local telephone company, such as call waiting.

TEMPORARY TONE DIALING

If you have pulse (rotary) service and want to access customer calling services (such as

telebanking and long distance services) that require tone dialing, you can use this feature to

temporarily change from pulse to tone service.

After dialing the telephone number and connecting to the customer calling service,

1. Press and release the TONE (*) button.

2. When you hang up, the telephone automatically returns to pulse dialing mode.

TIP: Temporary Tone can also be used while storing numbers in memory by pressing TONE

(*) at the necessary point in the storage sequence.

We bring good things to life.

Model 29385

00000737 (Rev. 2 E/S)

04-50

Printed in China

29385

Call Waiting Caller ID

Speakerphone with

13 Number Memory

User’s Guide

EQUIPMENT APPROVAL INFORMATION

Your telephone equipment is approved for connection to the Public Switched Telephone

Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the

Technical Requirements for Telephone Terminal Equipment published by ACTA.

1 Notification to the Local Telephone Company

On the bottom of this equipment is a label indicating, among other information, the US

number and Ringer Equivalence Number (REN) for the equipment. You must, upon request,

provide this information to your telephone company.

The REN is useful in determining the number of devices you may connect to your telephone

line and still have all of these devices ring when your telephone number is called. In most

(but not all) areas, the sum of the RENs of all devices connected to one line should not

exceed 5. To be certain of the number of devices you may connect to your line as

determined by the REN, you should contact your local telephone company.

A plug and jack used to connect this equipment to the premises wiring and telephone

network must comply with the applicable FCC Part 68 rules and requirements adopted by

the ACTA. A compliant telephone cord and modular plug is provided with this product. It is

designed to be connected to a compatible modular jack that is also compliant. See

installation instructions for details.

Notes

• This equipment may not be used on coin service provided by the telephone company.

• Party lines are subject to state tariffs, and therefore, you may not be able to use your

own telephone equipment if you are on a party line. Check with your local telephone

company.

• Notice must be given to the telephone company upon permanent disconnection of your

telephone from your line.

• If your home has specially wired alarm equipment connected to the telephone line,

ensure the installation of this product does not disable your alarm equipment. If you

have questions about what will disable alarm equipment, consult your telephone

company or a qualified installer.

2 Rights of the Telephone Company

Should your equipment cause trouble on your line which may harm the telephone network, the

telephone company shall, where practicable, notify you that temporary discontinuance of

service may be required. Where prior notice is not practicable and the circumstances warrant

such action, the telephone company may temporarily discontinue service immediately. In case

of such temporary discontinuance, the telephone company must: (1) promptly notify you of such

temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform

you of your right to bring a complaint to the Commission pursuant to procedures set forth in

Subpart E of Part 68, FCC Rules and Regulations.

The telephone company may make changes in its communications facilities, equipment,

operations or procedures where such action is required in the operation of its business and not

inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or

performance of your telephone equipment, the telephone company must give you adequate notice,

in writing, to allow you to maintain uninterrupted service.

INTERFERENCE INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference; and (2) This device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is

“receiving” the interference).

• Reorient or relocate and increase the separation between the telecommunications equipment

and receiving antenna.

• Connect the telecommunications equipment into an outlet on a circuit different from that to

which the receiving antenna is connected.

If these measures do not eliminate the interference, please consult your dealer or an

experienced radio/television technician for additional suggestions. Also, the Federal

Communications Commission has prepared a helpful booklet, “How To Identify and Resolve

Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing

Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering

copies.

HEARING AID COMPATIBILITY (HAC)

This telephone system meets FCC standards for Hearing Aid Compatibility.

US NUMBER IS LOCATED ON THE CABINET BOTTOM

REN NUMBER IS LOCATED ON THE CABINET BOTTOM

ATLINKS USA, Inc.

101 West 103rd Street

Indianapolis, IN 46290

Trademark(s) ® Registered

Marca(s) Registrada(s)

Modular

telephone

line jack

Wall plate

INTRODUCTION

CAUTION: When using telephone equipment, there are basic safety instructions that

should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS

provided with this product and save them for future reference.

Your Caller ID phone stores and displays specific information, provided by your local telephone

company, to subscribers of Caller ID or similar caller identification services.

Your Caller ID phone enables you to:

• Identify callers before you answer the phone.

• View the time and date of each incoming call.

• Record up to 75 Caller ID messages sequentially.

IMPORTANT: In order to use all of the features of this telephone, you must subscribe to two

separate services available from your local telephone company: the standard Name/Number

Caller ID Service to know who is calling when the phone rings and Caller ID with Call Waiting

Service to know who is calling while you are on the phone.

SHORT GLOSSARY OF TERMINOLOGY USED IN

THIS

MANUAL

Hook switch. The part of the phone that pops up to activate the phone line when the handset is

lifted from the base.

Off-hook. A term used to describe the phone in its active mode when the handset is off of the

base cradle or when the SPEAKER button is pressed.

On-hook. A term used to describe the phone in an inactive mode.

BEFORE YOU BEGIN

PARTS CHECKLIST

Make sure your package includes the following items:

TELEPHONE JACK REQUIREMENTS

To use this phone, you need an RJ11C type modular telephone jack,

which might look like the one pictured here, installed in your home. If

you don’t have a modular jack, call your local phone company to find

out how to get one installed.

IMPORTANT INSTALLATION INFORMATION

CAUTION: Disconnect the phone cord from the wall outlet before installing or

replacing the batteries.

• Never install telephone wiring during a lightning storm.

• Never touch uninsulated telephone wires or terminals, unless the telephone line has been

disconnected at the network interface.

• Use caution when installing or modifying telephone lines.

• Never install telephone jacks in wet locations unless the jack is specifically designed for

wet locations.

• Temporarily disconnect any equipment connected to the phone, such as faxes, other

phones, or modems.

INSTALLING AND REPLACING THE BATTERIES

Your Caller ID phone uses 4 AA-size alkaline batteries for receiving and storing Caller ID

records and for storing the numbers you use for memory dialing, pulse dialing, and redial.

IMPORTANT: You will have approximately 90 seconds to replace the batteries before the

memories stored are lost. Please read the instructions before replacing the batteries and have

the batteries ready to be inserted beforehand.

IMPORTANT: If you are not going to use the telephone for more than 30 days, remove the

batteries because they may leak and damage the unit.

1. If the telephone line cord is connected, disconnect it from the base unit.

2. Carefully turn over the phone, and press down and out on

the snap tab located on the top of the mounting bracket. Lift

the bracket off.

3. Release latch on battery compartments and remove cover.

4. Insert 4 AA-size alkaline batteries as shown on the diagram

in the battery compartments.

5. Snap the battery compartment doors back into place and

replace the mounting bracket.

6. If the line cord was previously connected, re-attach it to the

unit and check your memory locations.

NOTE: If the low battery icon appears in the display, you need to replace the batteries.

It is important that you replace the batteries as soon as possible in order to maintain

Caller ID operation.

INSTALLING THE PHONE

Your phone should be placed on a level surface, such as a desk or table top, or you can mount it on

a wall. A desktop/wall mounting pedestal is packaged with your phone.

ATTACHING THE DESKTOP PEDESTAL

• Turn the phone over so that the bottom of the base is facing up and the thickest end is

facing away from you.

• With the rounded end of the wedge pointing downward, insert the tab on the rounded end

of the pedestal into the middle slot on the bottom of the base, then push the pedestal down

until the two tabs on the left and right corners of the pedestal snap (lock) into the two upper

slots on the bottom of the base.

CONNECTING THE HANDSET

1. Connect one end of the coiled handset cord to the jack on the handset.

2. Plug the other end of the coiled handset cord to the jack on the base.

3. Place the handset in the cradle.

CONNECTING THE TELEPHONE LINE

1. Connect one end of the straight telephone line cord to the jack on the back of the base.

2. Connect the other end to a wall phone jack.

3. Set the RINGER volume switch located at

the back of the base to the desired

loudness.

OFF - Telephone will not ring.

LO - Sound will be lowest.

HI - Sound will be loudest.

NOTE: The unit is properly installed if you

pick up the handset and hear the dial tone.

Otherwise, recheck all installation steps.

WALL MOUNTING

Your speakerphone can also be mounted on a wall plate (not included).

ATTACHING THE WALL MOUNTING PEDESTAL

• Turn the phone over so that the bottom of the base is facing up and the thickest end is

pointing away from you.

• If desired gather the extra telephone line cord together and store inside the wall mounting

pedestal, and then thread the line cord through the grooves on the pedestal according to

the illustration.

MEMORY

You may store information in any of the following memory locations: 0 to 9, A, B, and C . See

“Storing a Pause in Memory” and “Temporary Tone Dialing” for more information.

STORING A NAME AND NUMBER IN MEMORY

1. Press the STORE button.

LOCATION?

shows in the display.

2. Press the desired memory location (0-9, A, B, C).

NOTE: You may select memory locations by pressing  or  to scroll through the memory

locations or press the 0 - 9, A, B, C.

3. Press the STORE button again to confirm the memory location.

NOTE: If necessary, to erase existing memories, or if you make a mistake, use the

DELETE button.

4. Use the number keys to enter the telephone number (up to 32 digits) and press the STORE

button to save. (The unit will not dial a phone number in this mode.) The cursor

automatically moves to the text line for name entry.

5. Use the number keys to enter the name of the person associated with the telephone number

you just entered. More than one letter is stored in each of the number keys.

For example, to enter the name BILL SMITH, press the 2 key twice for the letter B. Press the

4 key 3 times for the letter I. Press the 5 key 3 times for the letter L.

NOTE: The flashing cursor automatically moves to the next position or you may press

the  or  buttons to move the cursor to the next position.

Press the 5 key 3 times for the second letter L. Press the arrow key (4) two times to insert a

space, and press the 7 key 4 times for the letter S. Press the 6 key once for the letter M.

Press the 4 key 3 times for the letter I. Press the 8 key for the letter T. Press the 4 key twice

for the letter H.

6. Press the STORE button to save the name.

7. To enter another name and number in a different memory location, return to step 1 and

repeat the process.

CHANGING A STORED NUMBER

Repeat the storage sequence under Storing A Name and Number in Memory, and use the

DELETE button to delete the old number before entering the new number.

ERASING A STORED NUMBER

1. Press the STORE button.

2. Press the memory location (0-9, A, B, C) to be erased.

3. Press the DELETE button.

COPYING CALLER ID MEMORIES TO USER

MEMORY

1. Press the  or  buttons to view the caller number and name you want to copy.

2. Press the STORE button.

3. Press the memory location (0-9, A, B, C). The number flashes if there is a number already

stored in the memory location.

4. Press the STORE button to enter the edit mode, and then press the STORE button again to

edit the name.

NOTE: You may select a different memory location by pressing  or  to scroll through the

memories or press a number key (0-9, A, B, C).

5. Press the STORE button to confirm and save, and wait for three seconds to exit.

NOTE: If the name you want to enter is longer than 12 characters, only the first 12 characters

will be copied into memory.

COPYING REDIAL NUMBERS TO MEMORY

1. Press the REDIAL button while the phone is on-hook. The display shows

PICKUP PHONE

2. Press the STORE button.

3. Press any number key (0-9, A, B, C) for the memory location. The cursor flashes and allows

the user to enter the caller's name.

4. Press the STORE button twice to confirm and save, and wait for three seconds to exit.

NOTE: If you want to edit the number, press the STORE button again within three seconds.

When you are finished, wait three seconds to exit.

DIALING A NUMBER STORED IN MEMORY

WHILE ON-HOOK

1. Press the DIAL button

2. To select a memory, press any number key (0-9, A, B, C). The number in that memory

location displays.

NOTE: You may select a different memory location by pressing  or  to scroll through the

memories or press a number key (0-9, A, B, C).

3. Press the SPEAKER button, or pick up the handset to dial the displayed number.

DIALING A NUMBER STORED IN MEMORY

1. Lift the handset, or press the SPEAKER button.

2. Press the DIAL button then press a memory location button.

CASCADE DIALING

This process allows you to dial a succession of stored numbers from separate memory

locations. This is useful when you must dial several sequences of numbers, such as with

frequent calls via a telephone company long distance provider.

For example Memory location

Local access number of long distance company 6

Authorization code (ID) 7

Long distance phone number 8

1. Pick up the handset or press SPEAKER.

2. Press DIAL button, then press number “6” for the memory location.

3. Press DIAL button, then press number “7” for the memory location.

4. Press DIAL button, then press number “8” for the memory location.

5. The number dials automatically.

STORING A PAUSE IN MEMORY

The REDIAL button has dual functionality and becomes a pause button when the STORE button

is pressed first. It is valid only when storing a number into memory locations. Use the PAUSE

(REDIAL) button to insert a pause when a delay is needed in an automatic dialing sequence. For

example, when you must dial a 9 to get an outside line or when you enter codes to access your

long distance company.

PRE-DIALING

1. With the handset on the cradle, enter the telephone number you wish to call. The telephone

number shows in the display.

2. Lift the handset or press the SPEAKER button and the number automatically dials.

NOTE: Use the DELETE button to delete an incorrectly entered number.

TROUBLESHOOTING TIPS

No Dial Tone

• Check all cabling to make sure that all connections are secure and not damaged.

• Check hook switch: Does it fully extend when handset is lifted from cradle?

No Display

• Replace the batteries.

• Check for proper battery installation.

No Information is Shown After the Phone Rings

• Are you subscribed to Caller ID service from your local telephone company?

• Be sure to wait until the second ring before answering.

Phone Dials in Pulse with Tone Service

• Make sure T/P DIAL MODE is set to TONE DIAL.

Phone Won't Dial Out with Pulse Service

• Make sure T/P DIAL MODE is set to PULSE DIAL.

Phone Does Not Ring

• Make sure ringer switch is ON.

• You may have too many extension phones on your line. Try unplugging some extension

phones.

•Check for dial tone. See Troubleshooting Tips for No Dial Tone.

Incoming Voice Volume Low

• Are other phones off hook at same time? If so, this is normal condition as volume drops

when additional phones are used at once.

• Check the handset receiver or speaker volume.

Memory Dialing

• Make sure you entered the numbers correctly into memory.

GENERAL PRODUCT CARE

To keep your phone working and looking good, follow these guidelines:

• Avoid putting it near heating appliances and devices that generate electrical noise (for

example, motors or fluorescent lamps).

• DO NOT expose to direct sunlight or moisture.

• Avoid dropping and other rough treatment to the unit.

• Clean with a soft cloth.

• Never use a strong cleaning agent or abrasive powder because this will damage the finish.

• Retain the original packaging in case you need to ship it at a later date.

SERVICE

If trouble is experienced with this equipment, for repair or warranty information, please contact

customer service at 1-800-448-0329. If the equipment is causing harm to the telephone

network, the telephone company may request that you disconnect the equipment until the

problem is resolved.

This product may be serviced only by the manufacturer or its authorized service agents.

Changes or modifications not expressly approved by ATLINKS USA, Inc. could void the user’s

authority to operate this product. For instructions on how to obtain service, refer to the

warranty included in this guide or call customer service at 1-800-448-0329.

Or refer inquiries to:

ATLINKS USA, Inc.

Manager, Consumer Relations

P O Box 1976

Indianapolis, IN 46206

Attach your sales receipt to the booklet for future reference or jot down the date this product

was purchased or received as a gift. This information will be valuable if service should be

required during the warranty period.

Purchase date ________________________________________________

Name of store ________________________________________________

LIMITED WARRANTY

What your warranty covers:

• Defects in materials or workmanship.

For how long after your purchase:

• One year, from date of purchase.

(The warranty period for rental units begins with the first rental or 45 days from date of

shipment to the rental firm, whichever comes first.)

What we will do:

• Provide you with a new or, at our option, a refurbished unit. The exchange unit is under

warranty for the remainder of the original product’s warranty period.

How you get service:

• Properly pack your unit. Include any cables, etc., which were originally provided with the

product. We recommend using the original carton and packing materials.

• ”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that

the product is within the warranty period, must be presented to obtain warranty service.”

For rental firms, proof of first rental is also required. Also print your name and address and

a description of the defect. Send via standard UPS or its equivalent to:

ATLINKS USA, Inc.

c/o Thomson

11721 B Alameda Ave.

Socorro, Texas 79927

• Pay any charges billed to you by the Exchange Center for service not covered by the

warranty.

• Insure your shipment for loss or damage. ATLINKS accepts no liability in case of damage

or loss.

• A new or refurbished unit will be shipped to you freight prepaid.

What your warranty

does not

cover:

• Customer instruction. (Your Owner’s Manual provides information regarding operating

instructions and user controls. Any additional information, should be obtained from your

dealer.)

• Installation and setup service adjustments.

• Batteries.

• Damage from misuse or neglect.

• Products which have been modified or incorporated into other products.

• Products purchased or serviced outside the USA.

• Acts of nature, such as but not limited to lightning damage.

Product Registration:

• Please complete and mail the Product Registration Card packed with your unit. It will make

it easier to contact you should it ever be necessary. The return of the card is not required

for warranty coverage.

Limitation of Warranty:

• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS

PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE

HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY ATLINKS USA,

INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY

INCREASE THE SCOPE OF THIS WARRANTY.

• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE

REMEDY OF THE CONSUMER. ATLINKS USA, INC. SHALL NOT BE LIABLE FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR

ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS

PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED

BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY

APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY

PERIOD SET FORTH ABOVE.

How state law relates to this warranty:

• Some states do not allow the exclusion nor limitation of incidental or consequential

damages, or limitations on how long an implied warranty lasts so the above limitations or

exclusions may not apply to you.

• This warranty gives you specific legal rights, and you also may have other rights that vary

from state to state.

If you purchased your product outside the USA:

• This warranty does not apply. Contact your dealer for warranty information.

Base Handset Handset cord

Desktop/wall

mounting pedestal

2-wire telephone

line cord

DELETE

button

STORE

button

MUTE

button

VOL

button

REDIAL/PAUSE

button

FLASH/EXIT

button

DIAL

button

SPEAKER

button

CALLER ID DISPLAY MESSAGES

The following special messages indicate the status of a message or the unit:

BLOCKED CALL The caller of the incoming call is registered as “Private

Number” and their Caller ID information is withheld.

CALL WAITING Indicates a call is waiting on the line.

Battery power level is low.

NO CALLS The caller memory is empty.

START/END You are at the beginning or the end of the Caller ID memory log.

UNKNOWN CALLER The incoming call does not have Caller ID service or their service

area is not linked to yours. If

UNKNOWN CALLER

appears along

with a calling number, the name information for that number was

not available.

SPEAKERPHONE BASICS

display

1 2

Résumé du contenu

Page 1 - User’s Guide

• With the rounded end of the pedestal pointing upward,insert the tab on the end of the pedestal into the middle sloton the bottom of the base, then p

Page 2 - Guía del Usuario

Creamos cosas buenas para la vida.Model 2938500000737 (Rev. 2 E/S)04-5 0Impreso en China29385Teléfono con Altavoz,Identificador de Llamadas yLlamada e

Commentaires sur ces manuels

Pas de commentaire

Ge 00000737 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Téléphones Ge 00000737. GE 00000737 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Téléphones Ge 00000737