Ge 50975 GE Fluorescent Black Light Fixture 12 in Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Fournisseurs d'énergie Ge 50975 GE Fluorescent Black Light Fixture 12 in. GE 50975 GE Fluorescent Black Light Fixture 12 in User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 1
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
50975
Fluorescent
Battery Operated
Add safety and security to any room
Ideal for cupboards, closets, attics, basements, storage sheds
and garages
Requires 8 "AA"batteries
»<
y,t
jt t'J
t !•**
» #
»• «
.s • »*
INSTALLING BAHERIES:
Slide battery cap off end of light and install 8 "AA", 1.5 volt
batteries (not included) with polarity as shown on diagram
on the fixture. Replace cap. IMPORTANT: Different types of
batteries or new and used batteries should not be mixed.
Exhausted batteries should be removed from the fixture
and disposed of properly.
MOUNTING:
Your closet light can be mounted
using the supplied adhesive-back
"hook and loop" mounting strips.
Make sure surfaces are free of
dirt and grease before mounting.
1. Separate the supplied "hook
and loop" mounting strips
from each other, placing
the "hook" and "loop" sides
of the strips into two piles.
2. Peel back paper and apply
"loop" mounting strips to both
ends and middle of the back
ofthe closet light light.
3. Applythe "hook" strips to
the desired mounting
location, making sure they are
the same distance apart as
those on the closet light.
4. Press the closet light onto
the mounting surface.
NOTE: Allow one day for the adhesive backing to set before
attempting to pull closet light away from mounting surface.
Light can also be mounted using supplied screws.
TUBE REPLACEMENT:
1. Remove end caps from light
2. Remove transparent lens cover.
3. Twist the tube slightly in either direction to remove.
4. Replace with 8-watt, 12" F8T5/BLB black light bulb.
5. Replace tube cover and end caps.
CAUTION:
Do not turn on light with tube disconnected to avoid possible
damage to solid state circuit
Add safety and security to any room
Ideal for cupboards, closets, attics, basements, storage sheds
and garages
Requires 8 "AA"batteries
INSTALACIÓN DE LAS PILAS:
Deslice hacia afuera la tapa del extremo de la lámpara y coloque 8 pilas "AA"
de t5V (no incluidas) teniendo en cuenta el diagrama del aparato. Vuelva a
poner la tapa. IMPORTANTE: No se deben usar juntas distintos tipos de pilas o
pilas nuevas con pilas usadas. Saque las pilas gastadas del aparato y
deséchelas de forma adecuada.
INSTALACIÓN:
Puede instalar la luz de clóset con las cintas adhesivas de Velero™ incluidas.
Antes de la instalación, asegúrese de que las superficies no tengan ni polvo ni
grasa.
1. Despegue las cintas de Velero™ incluidas y colóquelas en dos pilas, una
con las cintas con "ganchos" y la otra con las cintas con "bucles".
2. Despegue el papel y coloque las cintas con los "bucles" en ambos extremos
y en el medio de la parte posterior de la lámpara de clóset.
3. Coloque la cinta con los "ganchos" donde quiera instalar la lámpara y
asegúrese de que la distancia entre ellas coincida con las cintas de la
lámpara.
4. Presione la lámpara de clóset contra la superficie donde la vaya a instalar.
NOTA: Deje que el pegamento se seque antes de intentar sacar la lámpara
del lugar donde la ha instalado.
También puede instalar la lámpara con los tornillos incluidos.
REEMPLAZO DEL TUBO
FLUORESCENTE:
1. Saque las tapas de los extremos
de la lámpara.
2. Saque la cubierta transparente
del lente.
3. Para sacarlo, gire ligeramente el
fluorescente en ambas
direcciones.
Vue de la page 0
1

Résumé du contenu

Page 1 - Fluorescent

50975FluorescentBattery OperatedAdd safety and security to any roomIdeal for cupboards, closets, attics, basements, storage sheds and garagesRequires

Commentaires sur ces manuels

Pas de commentaire