Ge 30 Electric Built-In Wall Ovens Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Poêles Ge 30 Electric Built-In Wall Ovens. GE 30 Electric Built-In Wall Ovens User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 16
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
,03257$17³ Save these instructions
for local inspector’s use.
,03257$17³ Observe all governing
codes and ordinances.
Note to Installer – Be sure to leave these
instructions with Consumer.
Note to Consumer – Keep these instructions
for future reference.
Skill level – Installation of this appliance
requires a qualified installer or electrician.
Proper installation is the responsibility
of the installer.
Product failure due to improper installation
is not covered under Warranty.
Product is for indoor use only.
Installation Instructions
27” & 30” Electric Built-In Wall Ovens
FOR YOUR SAFETY:
WARNING
:
Before beginning the installation, switch power off at the service panel and
lock the service disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.
Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,
stand or hang on the oven door.
Make sure the wall coverings, counters and cabinets around the oven can withstand the heat
(up to 200°F [93.3°C]) generated by the oven.
Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com
In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca
MATERIALS YOU MAY NEED
Junction Box
Wire Nuts
Strain Relief Clamp for 1/2” Conduit
TOOLS YOU MAY NEED
1/8” Drill Bit and Electric or Hand Drill
T20 Screwdriver
Phillips Screwdriver
Wire Strippers
1
REMOVE PACKAGING MATERIALS
Failure to remove packaging materials could result in damage to the appliance. Remove all packing
parts from oven, racks and heating elements. Remove protective film and labels on the outer door
and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping
screws securing the oven to the base pad. Open oven door and remove literature pack and oven
racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation
process. The trim is wrapped separately and taped to the top of the unit. Remove pedestal rails from
seperate box and set aside (30” Double Wall Ovens Only).
2
PREPARE THE OPENING
NOTE: If the cabinet does not have a solid bottom, two
braces or runners must be installed to support the weight
of the oven. For single ovens, the runners and braces
must support 200 lbs (91 kg). For double ovens, the
runners and braces must support 375 lbs. (170 kg).
NOTE: If marks, blemishes or the cutout opening are
visible above the installed oven, it may be necessary to
add wood shims under the runners and front trim until
the marks or opening are covered.
NOTE: If the cabinet does not have a front frame and
the sides are less than ¾” (1.9 cm) thick, shim both sides
equally to establish the cutout width.
ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired) into an
approved junction box. A plug and receptacle is NOT permitted on these products.
Suitable
Bracing
to Su
pp
ort
C
L
2" x 4" (5 cm x 10 cm)
or Equivalent Runners Level
with Bottom of Cutout
and Flush with Sides of Cutout
DESIGN INFORMATION
SINGLE OVEN INSTALLATIONS
The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also
be installed below a countertop or below specified cooktops. See the label on top of the oven for approved
models.
DOUBLE OVEN INSTALLATIONS
A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of the
oven for approved models.
IMPORTANT: Always refer to individual installation instructions packed with each product for specific
requirements.
Vue de la page 0
1 2 3 4 5 6 ... 15 16

Résumé du contenu

Page 1 - Installation Instructions

BEFORE YOU BEGINRead these instructions completely and carefully.• ,03257$17³ Save these instructions for local inspector’s use.• ,03257$17³ Obser

Page 2

2 B ABERTURA PARA HORNOS ÚNICOS – BAJO EL MOSTRADOR DE ENCIMERANOTA: Estos hornos sólo pueden instalarse bajo los modelos específicos como se indica

Page 3

2 D ABERTURA PARA INSTALACIÓN SOBRE UN CAJÓN CALENTADORNOTA: Instale el horno sólo con los modelos específicos listados en la etiqueta ubicada en la

Page 4

3 INSTALACIÓN DEL RIEL CON PEDESTAL (30” HORNOS DOBLES ÚNICAMENTE)A. Coloque un riel con pedestal en cada rodadura del gabinete o centrado en el lad

Page 5 - ELECTRICAL REQUIREMENTS

4 REMOCIÓN DE LA PUERTA (recomendada)NOTA: La remoción de la puerta no es un requerimiento de la instalación del producto, pero es una comodidad adic

Page 6 - MAKE ELECTRICAL CONNECTIONS

6 REALICE LAS CONEXIONES ELÉCTRICAS ADVERTENCIA: Desconecte la energía del panel de servicio y bloquee los medios de desconexión para evitar el accio

Page 7 - WARNING: Mounting screws

IMPORTANTE: Si esta unidad alguna vez se quita del gabinete o si el horno se quita de servicio, el reborde inferior debe quitarse antes o el reborde s

Page 8 - OPERATION CHECKLIST

13 CÓMO VOLVER A COLOCAR LA PUERTA DEL HORNONOTA: La puerta del horno es pesada. Puede necesitar ayuda para levantar la puerta lo suficiente como para

Page 9 - Instrucciones de instalación

2 A CUTOUT FOR SINGLE OVENS IN WALL CABINETNOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim both

Page 10

2 C CUTOUT FOR DOUBLE OVENS (2 THERMAL OVENS)NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim bot

Page 11 - 11-13 GE

3 PEDESTAL RAIL INSTALLATION (30” DOUBLE OVENS ONLY)A. Place one pedestal rail on each cabinet runner or centered on opposite side of solid cabinet

Page 12 - ÚNICAMENTE)

4 DOOR REMOVAL (RECOMMENDED)NOTE: Door removal is not a requirement for installation of the product but is an added convenience.To remove the door:A.

Page 13 - REQUISITOS ELÉCTRICOS

6 MAKE ELECTRICAL CONNECTIONSWARNING: Switch power off at the service panel and lock the service disconnecting means to prevent power from being swit

Page 14 - ADVERTENCIA

10 MOUNT THE OVENWARNING: Mounting screws must be used. Failure to do so could result in the oven falling out of the cabinet, causing serious injury.

Page 15

12 OVEN RACK GUIDE INSTALLATION (IF APPLICABLE)A. Locate included oven rack guide mouting hardware.B. Place oven rack guides on cavity wall studs wi

Page 16 - CORRESPONDE)

ANTES DE COMENZARLea estas instrucciones por completo y con detenimiento. • ,03257$17(³ Guarde estas instrucciones para el uso de inspectores locale

Commentaires sur ces manuels

Pas de commentaire