Ge HC HP Manuel d'utilisateur télécharger pdf (Page 12)

GE MDS Intrepid-HC HP Installation Guide

1-6

Assembling the Hanger Kit

The Hanger Kit is used to connect two RFUs and OCBs to the Pole Mount Kit. It consists of a single metal plate.

To assemble the Hanger Kit together with the RFU and OCB:

1. Place the RFU on the floor and hold it upright, as shown in the photo below.

2. Place the Hanger Kit in line with the OCB, as shown in the illustration below, and fasten the Kit to the OCB

using 3 large (M-10 type) screws.

Allen

Head

Screws

Hanger Bend

(to place on

the

Pole

Kit

)

Main

Extension

Diversity

Extension

Three Screws

Fastening the

Hanger Kit to

the

OCB

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 113 114

Intrepid-HC HP 1
Table of Contents 3
CLASS 1 LASER PRODUCT 4
子信息品有毒有害物申明 5
Chapter 1: Installation 7
GE MDS Intrepid-HC HP RFU 8
1+0/1+1 Installation 10
Assembling the Hanger Kit 12
Four Screws 13
Fastening the 13
Pole Mount Kit 13
RFU Cable Connections 17
2+2 XPIC Installation 18
Installation Components 19
Installation Procedure 19
N+1 Split Mount Installation 22
1+0 Configuration 25
1+0 SD Configuration 25
1+1 HSB Configuration 26
1+1 SD Configuration 26
1+1 FD Configuration 27
1+1 FD/SD Configuration 27
1+1 SD BBS Configuration 28
2+0 DP Configuration 29
2+0 SD DP Configuration 29
2+0 SP Configuration 30
2+0 SD SP Configuration 30
2+2 Hot Standby Dual Pole 31
2+2 HSB SP Configuration 32
2+2 SD DP Configuration 33
2+2 SD SP Configuration 34
2+2 FD SP Configuration 35
2+2 HSB FD DP Configuration 36
2+2 SD/FD DP Configuration 37
4+1 FD DP Configuration 38
5+1 FD DP Configuration 39
4+1 FD SD DP Configuration 40
5+1 FD SD DP Configuration 41
Defining IP Addresses 45
To define IP Addresses: 46
NMS PC Requirements 47
Starting the NMS 48
External Alarms Setup 54
Exiting the NMS 55
##*3 floorshelfIPbaseIP ++= 58
shelves. The subnet is not 59
Connecting Line Interfaces 74
Procedures 75
Site Acceptance Procedure 76
1+0 Commissioning Procedure 81
Management Verification 82
Loopback Operation 82
1+1 Commissioning Procedure 83
Switching Tests 84
XPIC Installation Guidelines 86
XPIC Commissioning Tests 87
XPIC Recovery Verification 88
2+2 Verification 88
3-15 89
3-17 91
Protection Connector Pin-Out 95
8 x E1/T1 Connector Pin-Out 95
E1/T1 Connector Pin-Out 97
10BaseT Connector Pin-Out 97
Configuring PPP 99
General 101
Frequency Channels 101
6H GHz (6.45-7.1 GHz) 104
7 GHz (7.1-7.9 GHz) 105
ITU-R 385-7 [0] 107
8 GHz (7.8-8.5 GHz) 111
IN CASE OF DIFFICULTY 113

Commentaires sur ces manuels

Pas de commentaire

Ge HC HP Manuel d'utilisateur Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Ge HC HP