Ge 31-10673 09-08 JR Manuel d'utilisateur télécharger pdf (Page 2)

DOOR REMOVAL (optional)

Door removal is not a requirement for installation of the product

but is an added convenience. To remove the door:

A. Open the oven door as far as it will go.

B. Push both hinge locks down toward the door frame to the unlocked posi-

tion. This may require a flat-blade screwdriver.

DO NOT LIFT THE DOOR BY THE HANDLE!

C. Place hands on both sides of the door, and close the oven door

to the removal position. (Approximately 1"-2" from the closed position.)

D. Lift door up and out until the hinge arms clear the slots.

NOTE: The oven door is very heavy. Be sure you have a firm grip before lift-

ing the oven door off the hinges. Use caution once the door is removed.

Do not lay the door on its handle. This could cause dents or scratches.

Hinge

unlocked

position

Hinge

slot

Hinge

arm

Rating

plate

Rating

plate

PREPARE THE RANGE

Protective

channel

STORAGE DRAWER REMOVAL

A. Pull drawer out until it stops.

B. Lift front of drawer until the stops clear the guide.

C. Pull forward and remove the drawer.

Rail

Guide

Stop

POWER CORD AND CONDUIT INSTALLA-

TION

A. Remove wire cover (on the back of range)

by removing screws using a 1/4" nut driver.

Do not discard these screws.

For power cord and 1" conduit only,

remove the

knockout ring (1

⁄

") located on bracket directly

below the terminal block. To remove the knockout,

use a pair of pliers to bend the knockout ring away

from the bracket and twist until ring is removed.

ELECTRICAL REQUIREMENTS

WARNING: This appliance must be properly grounded.

WARNING:

All new constructions, mobile homes, recreational vehicles and installations

where local codes do not allow grounding through neutral require a 4-conductor, UL-listed range cord.

WARNING: To prevent fire or shock, do not use an extension cord with this appliance.

WARNING: To prevent shock, remove house fuse or open circuit breaker before begin-

ning installation.

We recommend you have the electrical wiring and hookup of your range connected by a qualified

electrician. After installation, have the electrician show you how to disconnect power from the range.

You must use a single-phase, 120/208 VAC or 120/240 VAC, 60 hertz electrical system. If you

connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring

must be used.

Effective January 1, 1996, the National Electrical Code requires that new construction (not existing)

utilize a 4-conductor connection to an electric range. When installing an electric range in new con-

struction, mobile home, recreational vehicle, or an area where local codes prohibit grounding

through the neutral conductor, refer to the section on four-conductor branch circuit connections.

Check with your local utilities for electrical codes which apply in your area. Failure to wire your

oven according to governing codes could result in a hazardous condition. If there are no local

codes, your oven must be wired and fused to meet the National Electrical Code, NFPA No. 70 –

latest edition, available from the National Fire Protection Association.

This appliance must be supplied with proper voltage and frequency and connected to an individ-

ual, properly grounded, 40 amp (minimum) branch circuit protected by a circuit breaker

or time-delay fuse.

Use only a 3-conductor or a 4-conductor UL-listed range cord.

These cords may be provided with ring terminals on wire and

a strain relief device.

A range cord rated at 40 amps with 125/250 minimum volt range

is required. A 50 amp range cord is not recommended, but if used,

it should be marked for use with nominal 1

⁄

" diameter connection

openings. Care should be taken to center the cable and strain relief

within the knockout hole to keep the edge from damaging the cable.

The rating plate is located on the oven frame or on the side

of the drawer frame.

Knockout

ring in

bracket

Knockout ring

removed

Terminal block

(appearance

may vary)

ALTERNATE INSTALLATION / CONSTRUCTION KITS

Description:

Backguard Kit: Adds a decorative backguard to the rear

of the range. This kit can only be used when the opening

in the countertop is 25" deep.

Maintop Filler Kit: Adds a filler strip to the rear of the range.

This kit can only be used when the opening in the countertop

is 25" deep. This kit cannot be used with a backguard kit.

Body Side Kit: Contains a color-matched side panel which

can be used to create a finished appearance on either side

of the range.

Lower Trim Kit: Contains a color-matched toe kick

and extra-long leveling legs. Designed to be used when

the range needs to be raised higher than 36-1/2".

Use:

Designed to be used when replacing

a free-standing range with a slide-in.

Used to fill gap between the range

back and wall.

Designed to be used when cabinets

are absent on one side of the range.

Use kit when countertop height is

36-1/2" to 38" high.

To order accessory kits, call 1.866.775.4557, or visit www.GEAppliances.com.

Hinge clears slot

Wire

cover

1 2 3 4

Commentaires sur ces manuels

Pas de commentaire

Ge 31-10673 09-08 JR Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Radio Ge 31-10673 09-08 JR