Specification Created 3/04
120034
ZIBI240PII – GE Monogram Bar Refrigerator with Icemaker Module
(Custom panel required)
ZIBS240PSS – GE Monogram Bar Refrigerator with Icemaker Module
(Stainless steel)
Dimensions and Specifications (in inches)
34-1/2" - 35"
24" Min.
47-1/2" Min.
1-1/2"
Locate Outlets
9"
Max.
10-1/2"
1-1/2"
9"
Max.
10-1/2"
24"
For a complete food storage center, install two Monogram refrigeration
modules side-by-side.
Note: Reversible door swing on wine chillers/reserves and beverage
centers only. See below for combination cutout dimensions.
Important Note: Products must operate from separate, properly
grounded receptacles.
Grounding the Bar Refrigerator with Icemaker
IMPORTANT – (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
The power cord of this appliance is equipped with a 3-prong
(grounding) plug which mates with a standard 3-prong (grounding)
wall receptacle to minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to
make sure the outlet is properly grounded.
When a standard 2-prong wall outlet is encountered, it is your
personal responsibility and obligation to have it replaced with a
properly grounded 3-prong wall out.
DO NOT, UNDER ANY CIRCUMSTANCES,
CUT OR REMOVE THE THIRD (GROUND)
PRONG FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE
REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.
Note: Additional cutout width may be required for models with
custom panels.
3/4” Overlay Panel Dimensions
Model ZIBI240PII requires customer-provided
overlay door panel.
• The overlay panel must be secured to a 1/4"
thick backer panel which slides into the trim.
A .10" thick spacer panel must be placed
between the custom and backer panel.
• A custom handle, supplied by your cabinet
maker, must be installed on the overlay panels.
Overlay
Panel
1/4"
Backer
Panel
Door
.10 Inch
Spacer
3/4" Overlay Panel Dimensions (in inches)
A (Width) B (Height)
1/4" Backer 23-3/16" 29-9/16"
0.10" Spacer 22-1/2" 29-1/16"
3/4" Overlay 23-5/8" 30"
NOTE: Max. assembled drawer panel weight
is 25 lbs.
Assemble overlay panels with glue
and screws.
• Center spacer panel on the backer panel,
left to right and top to bottom. Secure
the panels with glue.
• Center the spacer/backer panel on
the overlay panel. Secure with glue
and screws. Countersink screws into
the backer panel.
Spacer Panel
Backer Panel
Overlay Panel
For answers to your Monogram,
®
GE Profile
™
or
GE
®
appliance questions, visit our website at
GEAppliances.com or call GE Answer Center
®
service, 800.626.2000.
Listed by
Underwriters
Laboratories
Use a 3/4" router bit to cut a notch into the back side
of the assembled panel to allow for hinge clearance.
A
B
3/4" Deep
7/8" Wide
3/8" toward
the front side
Back Side
of Panel
(5 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels