GE 01978HD Manuel d'utilisation et d'entretien télécharger pdf

50/100/150 LIGHTS

FOR INDOOR USE ONLY

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products, basic precautions should always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When

products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI)

outlet. If one is not provided, contact a qualified electrician for proper installation.

This seasonal use product is not intended for permanent installation or use.

Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.

Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.

Do not let lamps rest on the supply cord or on any wire.

Unplug the product when leaving the house, when retiring for the night, or if left unattended.

This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it should

not be played with or placed where small children can reach it.

Do not use this product for other than its intended use.

Do not hang ornaments or other objects from cord, wire, or light string.

Do not place lighting string on carpeting, drapes, furniture, or allow it to contact vinyl siding while the power is on.

Do not perform any maintenance or troubleshoot for bad or broken lamps while the power is on.

Do not close doors or windows on the product or extension cords as this may damage the wire insulation.

Do not cover the product with cloth, paper or any material not part of the product when in use.

This product is equipped with push-in type lamps. Do not twist lamps.

This product employs overload protection (fuse). A blown fuse indicates an overload or short -circuit

situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products

that may be attached to the product, Replace the fuse as per the user servicing instructions (follow product

marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be

present and the product should be discarded.

ith the product. Read and follow all instructions that are on the product or provided w

SAVE THESE INSTRUCTIONS

USE AND CARE INSTRUCTIONS

When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on

live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.

If the product is placed on a tree, the tree should be well secured and stable.

Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed

wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.

When storing the product, carefully remove the product from wherever it is placed, including tree, branches,

or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.

When not in use, store neatly in a cool, dry location protected from sunlight.

USER SERVICING INSTRUCTIONS

Fuse replacement:

Most often, fuses blow because too many sets have been strung end-to-end.

Before changing fuses, make sure the set is unplugged

Grasp plug and remove from the receptacle or other outlet device.

Do not unplug by pulling on cord.

Using a flathead screwdriver, open fuse cover. Slide open

the fuse access cover on top of attachment plug towards blades.

Remove fuses carefully.

Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with product).

Close fuse cover. Slide closed the fuse access cover on top of attachment plug.

Make sure door is fully closed and fuses are completely covered.

Risk of fire. Do not replace attachment plug. Contains a safety device (fuse)

that should not be removed. Discard product if the attachment plug is damaged.

-SEE OTHER SIDE-

MODEL NO.

CFPS(I)-50(0.17)

CFPS(I)-100/2F(0.34)

CFPS(I)-150/3F(0.51)

IM-56

CONTINUED FROM OTHER SIDE-

CAUTION:

This string contains two different types of

Replaceable bulbs-steady-illuminating and fuse bulbs.

REPLACEABLE FUSED LAMPS – identified by the white colored ring.

There is one fuse bulb for each lighted circuit of 50 bulbs.

REPLACEABLE

FUSED LAMPS –

identified by the white

colored rin

lways replace burned-out bulbs promptly. If a number of bulbs are burned out,

extra stress is put on the remaining bulbs in the circuit. This may cause additional

bulbs to burn out prematurely. When a fuse bulb fails the entire circuit will not light.

Before changing bulbs, make sure set is unplugged.

Replace Steady Bulb NOTE:

Steady and Fuse bulbs are not interchangeable.

If the spare bulbs provided with the product have no plastic base or

he plastic base does not fit, first follow steps 1 – 2 above. Then

a) Remove the old bulb by straightening the bulb wires and

pulling bulb straight from the base.

b) Replace the new bulb by straightening the bulb leads and

aiming each wire into a separate hole in the plastic base.

c) Make sure each bulb lead comes out an exit opening at the bottom of the plastic base.

Now bend each lead up such that each bulb lead fits closely against the narrow side of the plastic base.

Replace Fuse Bulb NOTE:

Fuse bulbs are secured in the base with adhesive. Do not attempt to remove.

R replace with only 2.5 Volt, 0.425 Watt fuse bulbs provided with product.

emo

ve old fuse bulb and

CAUTION:

1.This lighting string is rated

50 /100 /150: 2

.4 / 40.8 / 61.2 Watts (0.17 / 0.34 / 0.51

Amps), do not overload.

2. To reduce the risk of overheating replace burned-out lamps promptly. Use 2.5 Volt, 0.425 Watt lamps only.

3.To reduce the risk of fire and electric shock: a) Do not install on trees having needles, leaves or branch

coverings of metal or materials which look like metal, and b) Do not mount or support strings in a manner that

sulation. can cut or damage wire in

WARNING:

Risk of fire. This product employs overload protection (fuse bulb) in each series circuit

to provide overload protection in addition to the fuse(s) located in the plug. Do not replace the fuse bulb

ntained in this set with any other type of bulb. Use only spare fuse bulbs provided with this product. co

For questions and/or assistance, call customer service at 1-877-398-7337

or visit us on the web at

www.geholidaylighting.com

FP-15 PRINTED IN CHINA

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE CORRECTIVE ACTION

If the product

does not light

One or more of the based bulbs may

have loosened from the socket during

transporting. There is a break in the

circuit between the bulb leads and the

socket terminals. Fuse(s) may have

moved.

Unplug the set at the outlet. Starting with the

first unlit bulb, gently push (don't twist) each

bulb base firmly into the socket. If still does

not light, then remove each based bulb to

check for out of place lead wires. Open fuse

door and check fuses.

If a bulb is

broken

Bulbs may have hit against each other

when transporting

Mark socket(s) with a piece of tape and

unplug the set before removing the based

bulb from the socket. Replace the broken

bulb. Should another bulb flicker while doing

this that is a faulty bulb. Replace with a new

bulb.

If a based bulb

is missing

One or more of the based bulbs may

have come out of the socket when

transporting

Mark socket with a piece of tape and unplug

the set. Replace based bulb or use one of

the spare based bulbs included with product.

If a bulb

burns out

Incorrect bulb, premature bulb failure or

voltage is too high

The remaining bulbs should remain lit.

However, it is best to replace burned out

bulbs as soon as you find them.

tep

ace

ly 2

super bright midget push-in type

lamp provided with product.

Push spare bulb/base assembly into socket.

Do not twist bulb when inserting into socket.

If bulbs are twisted, part of the set will not light.

tep

rasp

remove

rom

receptacle or other outlet device.

Do not unplug by pulling cord.

Step 2: Hold bulb by the plastic base

and pull bulb/base straight

out of socket.

1 2

Résumé du contenu

Page 1 - TROUBLESHOOTING

50/100/150 LIGHTS FOR INDOOR USE ONLY IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed in

Page 2

50/100

Commentaires sur ces manuels

Pas de commentaire

GE 01978HD Manuel d'utilisation et d'entretien

Naviguer en ligne ou télécharger Manuel d'utilisation et d'entretien pour Lampes de travail GE 01978HD. GE 01978HD Use and Care Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels