GE EDW3000G02 Manuel d'utilisateur télécharger pdf (Page 3)

STEP ACTION LED DISPLAY DESCRIPTION

1 Start

2 Model Number Display

3 Illuminate Display All LED’s Energize all LEDs for 5 seconds.

4 Trip Detergent & Fill DRYING, SANITIZED

5 Fill & Circulate RINSING

6 Circulate & Heat RINSING, SANITIZED

7 Calibration SENSING

8 Circulate & Drain RINSING, DRYING

9 Circulate RINSING, DRYING, SANITIZED

10 Trip Rinse Agent & WASHING

Self diagnostics

11 Fill WASHING, SANITIZED

12 Fill & Circulate WASHING, DRYING

13 Circulate & Heat WASHING, DRYING, SANITIZED

14 Auxiliary Pump All LED’s

15 Auxiliary Pump WASHING, RINSING,

SANITIZED

16 Exit

THIS DISHWASHER IS PROGRAMMED WITH A SERVICE

MODE TO AID THE TECHNICIAN IN TROUBLESHOOTING

THE DISHWASHER. EACH COMPONENT MAY BE CYCLED

TO DETECT IF IT IS FUNCTIONING CORRECTLY. COMPO-

NENTS ARE CYCLED BY PRESSING KEYPADS TO THE LEFT

OF THE START/RESET KEYPAD. USE THE MATRIX BELOW

TO DETERMINE HOW TO CYCLE EACH COMPONENT.

*NOTE: After 15 minutes of inactivity, the service mode will

automatically turn off.

**NOTE: Component will be activated for indicated time.

Component may be deactivated by pressing the same keypad

that was pressed to activate the component.

165D6290G028

MODELS WITH A TURBIDITY SENSOR

NOTE: INDICATES KEYPAD USED ONLY ON

SOME MODELS.

TO ENTER SERVICE MODE :

PRESS KEYPAD #9 AND KEYPAD #3 SIMULTANEOUSLY FOR 3

SECONDS.

TO EXIT SERVICE MODE :

PRESS THE START/RESET KEYPAD AT ANYTIME TO EXIT.

Service Mode Test Matrix*

Keypad Description Time in Seconds**

9 Activates Water Valve 50

8 Activates Heating Element 600

7 Activates Main Pump 75

6 Activates Detergent Module 60

5 Activates Drain Pump 75

3 Activates the following in order: 3 seconds each cycle

Status LEDs; Wash LEDs;

Start/Reset and Option LEDs

2 Opens Active Vent

1 Closes Active Vent

START/RESET Used to EXIT Service Mode

1098765 3421

TO ENTER F-1 TEST CYCLE:

1. Power up unit.

2. Close detergent cup and latch door.

3. Press KEYPAD #9 and KEYPAD #8 simultaneously for

one second. The control will then step through the test

automatically.

TO EXIT F-1 TEST CYCLE:

1. Press START/RESET to skip each step until the end.

2. The control will then exit the test cycle, pump out any

remaining water and return to normal operation.

F-1 TEST CYCLE MATRIX

SENSING and WASHING flash

for 10 seconds

Combination of KEY 1 (LOCK)

and DELAY START 1, 2 or 3

NOTE: DELAY START 1, 2 & 3 represent the

leftmost, middle and rightmost

DELAY START

LEDs, respectively.

In STEP 10 of the F1 Test Cycle: If the control senses a turbidity sensor error, the control

will flash the SENSING LED. If the control senses a tub temperature sensor error, then the

control will flash the HEATED DRY LED. If the control senses an EEPROM error, then the

control will flash the LOCK LED.

If any of these diagnostic errors are detected, the cycle

will not advance to STEP 11 until a key is pressed.

Use KEY 1 (MS3) and DELAY

START LEDs to display model

number in binary for 5 seconds

Trip the detergent cup. Energize

the water valve for 50 seconds.

Energize the water valve and

main pump for 10 seconds.

Close the active vent.

Energize the main pump and

heater for 60 seconds.

All relays and LEDs will be off

while the processor calibrates

the turbidity sensor.

Energize the main pump and

auxiliary pump to evacuate water

from the unit for 10 seconds.

Energize the main pump to

circulate water in the unit for

50 seconds.

Trip the rinse agent. Read

Turbidity Sensor. Read tub

temperature sensor. Read

EEPROM. If diagnostics or turbidity

errors occur, energize the beeper

and flash LEDs (see below).

Energize the water valve for 50

seconds.

Energize the water valve and main

pump for 3 seconds.

Energize the main pump and

heater for 60 minutes.

Energize all LEDs and the auxiliary

pump to evacuate water for 5

seconds. Open the active vent.

Energize the auxiliary pump to

evacuate water from the unit for

70 seconds.

1 2 3 4

Commentaires sur ces manuels

Pas de commentaire

GE EDW3000G02 Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle GE EDW3000G02