GE GDF520PSFSS Manuel d'instructions télécharger pdf (Page 10)

Dishwasher Installation

STEP 15: POSITION DISHWASHER, SECURE

TO COUNTERTOP OR CABINET

In this step you will need the 2 Phillips special head screws

from the screws set aside in Step 1.

The dishwasher must be secured to the countertop or the

cabinet sides. When the underside of the countertop is wood,

use Method 1. Use Method 2 when the underside of the

countertop is made of a material, such as granite, that will not

accept wood screws.

IMPORTANT – Prevent door panel and control

panel damage. Dishwasher must be positioned so the front

panel and control panel do not contact the adjacent cabinets

or countertop. Mounting screws must be driven straight and

flush. Protruding screw heads could scratch the door panel or

control panel and interfere with door operation.

Method 1

Secure dishwasher to underside of wood countertop.

• Recheck alignment of the dishwasher in the cabinet. Refer to

Steps 13 and 14. Door panel and/or control panel must not

hit cabinets or countertop.

• Fasten the dishwasher to the underside of the countertop

with the 2 Phillips special head screws. Refer to Figure T.

0DNHFHUWDLQVFUHZVDUHGULYHQVWUDLJKWDQGÀXVKWRSUHYHQW

panel damage.

• Install plug buttons to the side of the tub well in the holes

provided.

Method 2

Secure dishwasher to cabinet sides.

• Recheck alignment of the dishwasher in the cabinet. Refer to

Steps 13 and 14. Door panel and/or control panel must not

hit cabinets or countertop.

• Fasten the dishwasher to the adjacent cabinets with the 2

Phillips special head screws provided. Refer to Figure U. Make

FHUWDLQVFUHZVDUHGULYHQVWUDLJKWDQGÀXVKWRSUHYHQWSDQHO

damage.

• Install plug buttons to the side of the tub well in the holes

provided.

Figure U

Figure T

Brackets

Wood Countertop

Granite Countertop

Side Brackets

STEP 16: CONNECT WATER SUPPLY

Connect water supply line to 90° elbow.

If using a flexible braided hose connection:

• Attach nut to 90° elbow using an adjustable wrench.

If using a copper tubing connection:

• Slide compression nut, then ferrule over end of water line.

• Insert water line into 90° elbow.

• Slide ferrule against elbow and secure with compression nut.

IMPORTANT – Check to be sure that door spring

DQGRUGRRUVSULQJFDEOHGRQRWUXERUFRQWDFWWKH¿OOKRVHRU

water supply line.

Test by opening and

closing the door.

Reroute the water

supply lines if a

rubbing noise or

interference

occurs.

STEP 17: CONNECT DRAIN LINE

The molded end of the drain hose will fit 5/8" through 1"

diameter inlet ports on the air gap, waste tee or disposer.

• Determine size of inlet port.

• Cut drain hose connector on the marked line, if required,

WR¿WWKHLQOHWSRUW

• If a longer drain hose is required and you did not purchase

drain hose GPF12L, add up to 66" length for a total of 144"

(12 feet) to the factory-installed hose. Use 5/8" or 7/8" inside

diameter hose and a coupler to connect

the 2 hose ends.

Secure the

connection

with hose

clamps.

Figure W

Figure X

NOTE: TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 12 FEET

FOR PROPER DRAIN OPERATION.

7^bT2[P\_

2^d_[Ta

7^bT2[P\_

Cutting Line

5/8"

IMPORTANT: Do not cut corrugated

portion of hose

Figure V

Compression

Nut

Hot Water

Supply Line

90° Elbow

Ferrule

Bottom Left Side

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

GE GDF520PSFSS Manuel d'instructions Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle GE GDF520PSFSS