GE WMK35 Brochure télécharger pdf (Page 81)

Built-In Room Air Conditioners Specifications

Heat/Cool Specifications

See page 83 for warranty information.

Wall opening for RAB46/47/48 Cases

A finished opening of 26-1/8"

x 15-3/4", clear

of intrusions, is required. Keep clearance of

4" from side walls. Brick veneer or frame walls

should have wood studding surrounding case

to provide firm anchoring with screws. Case

can be fastened directly to brick or block walls

with screws sunk in lead expansion shields.

Note: Units should be caulked on all four

sides of case to the building exterior to assure

building integrity.

Built-in RAC Installation

(Pub. 1-G003 pg. 138) April 30.1993

Make frame if desired or caulk

between case and siding

15-3/4

26-1/8

Frame Construction

Brick Block and Brick

Frame Construction

Fill open cells

with mortar

or insulation

15-3/4

26-1/8

Lintel

OUTSIDE INSIDE

16-7/8

Caulking

Drip Rail

Trim Molding

(if desired)

Plaster Line

Built-In Room Air Conditioners

Wall Opening for RAB36/37/38 Case

A finished opening of 26-1/8" x 15-3/4", clear of

intrusions, is required. Keep clearance of 4" from

side walls. Brick veneer or frame walls should have

wood studding surrounding case to provide firm

anchoring with screws. Case can be fastened directly

to brick or block walls with screws sunk in lead

expansion shields.

Flexible Mounting Position

Built-in RAC Installation

(Pub. 1-G003 pg. 138) April 30.1993

Make frame if desired or caulk

between case and siding

15-3/4

26-1/8

Frame Construction

Brick Block and Brick

Frame Construction

Fill open cells

with mortar

or insulation

15-3/4

26-1/8

Lintel

OUTSIDE INSIDE

16-7/8

Caulking

Drip Rail

Trim Molding

(if desired)

Plaster Line

Built-In Room Air Conditioners

Wall Opening for RAB36/37/38 Case

A finished opening of 26-1/8" x 15-3/4", clear of

intrusions, is required. Keep clearance of 4" from

side walls. Brick veneer or frame walls should have

wood studding surrounding case to provide firm

anchoring with screws. Case can be fastened directly

to brick or block walls with screws sunk in lead

expansion shields.

Flexible Mounting Position

Built-in RAC Installation

(Pub. 1-G003 pg. 138) April 30.1993

Make frame if desired or caulk

between case and siding

15-3/4

26-1/8

Frame Construction

Brick Block and Brick

Frame Construction

Fill open cells

with mortar

or insulation

15-3/4

26-1/8

Lintel

OUTSIDE INSIDE

16-7/8

Caulking

Drip Rail

Trim Molding

(if desired)

Plaster Line

Built-In Room Air Conditioners

Wall Opening for RAB36/37/38 Case

A finished opening of 26-1/8" x 15-3/4", clear of

intrusions, is required. Keep clearance of 4" from

side walls. Brick veneer or frame walls should have

wood studding surrounding case to provide firm

anchoring with screws. Case can be fastened directly

to brick or block walls with screws sunk in lead

expansion shields.

Flexible Mounting Position

Standard Wall Case RAB46

Solid-sided wall case fabricated of galvanized

steel with baked enamel finish. Welded areas

are coated with a sealing compound to help

resist rust and corrosion. Polymer gasket

surrounds opening to assure tight weather

seal. Aluminum grille (RAG13) is included.

Panels on interior and between case and grille

provide weather protection prior to installation

of chassis.

Two Wall Cases for Tenant Option Installation

When the air conditioner is offered as a tenant

option, these wall cases provide protection

against outside elements.

RAB47—includes wall case, exterior grille and

steel closure panels.

RAB48—includes wall case, exterior grille,

steel closure panel and two layers of

insulation.

REMOVE WEA

THER P ANEL

BEFORE INST

ALLING CHASSI

DIRECTIONS:

PULL T

AB WHERE NOTED

AND REMOVE ENTIRE WEA

THER

ANEL

( SHADED AREA)

T O

ENSURE PROPER UNIT PERFORMANCE.

PULL

REMOVE

PANEL

CAUTION

Wall Outlets

All wiring, including installation of receptacle, must be made in accordance with local

electrical codes and regulations. Electrical outlet should be in reach of line cord.

Note: Aluminum wiring may pose special problems—consult a qualified electrician.

Note: Some models may not be available in your area due to local legislation.

Contact your local dealer.

Note: When installing slide out chassis units in through-the-wall applications, keep

louvers free. Do not restrict air flow areas. Fixed chassis units are not suitable for

through-the-wall applications.

Parallel

115V.

15 Amp.

Ta n d e m

230/208V.

15 Amp.

Perpendicular

230/208V.

20 Amp.

Listed by

Underwriters

Laboratories

Total capacity and E.E.R. ratings

are calculated based on the

Association of Home Appliance

Manufacturers’ standards.

Model AGE12DB AGE14DA AGE18DA AGE21DA

Voltage 230/208 230/208 230/208 230/208

Cooling Capacity

BTUH-AHAM 12,000/11,500 14,000/13,500 18,000/17,500 21,000/20,500

Amps-AHAM 5.5/5.8 6.4/6.8 8.3/9.0 10.8/11.8

Watts Input 1,220/1,170 1,440/1,390 1,850/1,800 2,470/2,410

EER 9.8/9.8 9.7/9.7 9.7/9.7 8.5/8.5

Dehumidification (Pts./Hr.) 3.3 4.6 5.5 6.3

Electric Resistance Heating

BTUH 11,200/9,200 11,600/9,400 11,600/9,400 11,600/9,400

Amps 15.3/14 16/15 16/15 16/15

Watts Input @ 230V 3,500/2,900 3,670/3,100 3,670/3,100 3,720/3,150

Features

Line Cord Plug Perp. Perp. Perp. Perp.

Recommended Circuit Protection

(Time Delay) 20 Amps 20 Amps 20 Amps 20 Amps

Fan Speeds, Heating/Cooling 2/2 2/2 2/2 2/2

Fan Only Setting 1 1 1 1

Air Flow (CFM) Roomside Hi/Low 300 434 425 405

Air Exchange Exhaust

• • • •

Rotary Compressor

• • • •

Slide-Out Chassis

• • • •

Window Installation Kit EZ Mount EZ Mount EZ Mount EZ Mount

Approximate Net Weight (Lbs.) 90 112 120 135

Approximate Shipping Wt. (Lbs.) 96 125 133 143

Heat/Cool Units

1 2 ... 76 77 78 79 80 81 82 83 84

Commentaires sur ces manuels

Pas de commentaire

GE WMK35 Brochure Page 81

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle GE WMK35