Ge 26995 Manuel d'utilisateur télécharger pdf (Page 2)

REVIEWING AND DELETING STORED

NUMBERS

1. Press MEMORY, then use the arrow keys to view the

entry.

2. While the entry is displayed, press DELETE to delete the

entry. The display shows

ERASE MEMO?

3. Press DELETE a second time to delete the entry.

CHAIN DIALING FROM MEMORY

Use this feature to make calls which require a sequence of

numbers such as using a calling card for a frequently

called long distance number. Basically, you dial each part

of the sequence from memory. The following example

shows how you can use chain dialing to make a call

through a long distance service:

The Number For Memory Location

Long distance access number 7

Authorization code 8

Frequently called long distance number 9

1. Make sure the phone is ON.

2. Press MEMORY and then press 7.

3. When you hear the access tone, press MEMORY and

then press 8.

4. At the next access tone, press MEMORY and then 9.

TIP: Wait for the access tones before pressing the next

memory button, or your call might not go through.

CALLER ID BOX BASICS

REMOTE UNIT IDENTIFICATION CODE

SET UP

1. Place the remote Caller ID box next to the base.

2. Press and hold the MENU button on the box for 3

seconds. The display shows

SET CODE

3. Within 10 seconds, press and hold the PAGE button on

the base for 3 seconds.

4. The base will automatically send the ID code to the

remote Caller ID box. The display shows

ID SET

and the

unit confirms with a tone.

5. The display will then return to the default display.

CALLER’S NUMBER/NAME DISPLAY

When you receive a call, the caller’s number, name and

date/time of call will be stored in the Caller ID memory. Up

to 99 Caller-ID records can be stored in the remote unit.

When the memory is full, the oldest calls are deleted to

make room for newer calls.

• The icon NEW displays when a new Caller ID record is

received or that record is not viewed during standby.

REVIEW CALLER ID RECORDS

As calls are received and stored, the display is updated to

let you know how many calls have been received.

• To review the Caller ID records, press either of the

arrow buttons.

• The display shows

END OF LIST

when end of list is

reached.

ERASE CALLER ID RECORD

To erase a single Caller ID record:

1. Use the arrow buttons to select any stored record.

2. Press DELETE button. The display will show

ERASE

CALL ID?

3. Press DELETE button again to erase the entry.

To Erase All Caller ID records:

1. Use the arrow buttons to select any stored record.

2. Press and hold DELETE button for 3 seconds. The

display shows

ERASE ALL ?

3. Press DELETE button again to erase all stored records.

VOICE MESSAGE WAITING

NOTIFICATION

Provided your phone company offers voice messaging

service and you subscribe to it, this feature allows callers

to leave messages while you talk on the phone or if you

are unable to answer the call. A Waiting Icon will display if

you have a voice mail message. The icon will not display

after the message has been reviewed.

LOW BATTERY NOTIFICATION

The low battery displays whenever there is low battery or

when no batteries are installed.

ANNOUNCING CALLS IN MEMORY

Press the arrow buttons simultaneously to announce all

the Caller ID records (from latest to oldest) with all Name/

Number/Date/Time information.

HEADSET AND BELT CLIP

OPERATION

CONNECTING A HEADSET TO THE

HANDSET

For hands free conversation, connect the headset

(optional) to the HEADSET jack as shown. The handset

receiver and microphone are disabled when the headset is

connected.

Ni-Cd

RBRC

Adjust the headset to rest

comfortably on top of your

head and over your ear.

Move the microphone to

approximately 2 to 3

inches from your mouth.

• Press the TALK button

to answer or place a

call before using the

headset.

CONNECTING

THE

BELT CLIP

There are two slots, one

on each side of the

handset.

• Attach the belt clip by

inserting the sides of

the belt clip into the

slots. Snap the ends of

the belt clip into place.

CHANGING THE BATTERY

Make sure the telephone is OFF

before you replace battery.

1. Remove the battery compartment

door.

2. Disconnect the cord attached to

the battery pack and remove the

battery pack from the handset.

3. Insert the new battery pack and

connect the cord into the jack

inside the handset.

4. Put the battery compartment

door back on.

5. Place handset in the base to

charge. If you don’t charge the

handset battery properly (for 12 hours)

when you first set up the phone and/or when you install a new

battery pack, the battery’s long-term performance will be

compromised.

BATTERY SAFETY PRECAUTIONS

• Do not burn, disassemble, mutilate, or puncture. Like

other batteries of this type, toxic materials could be

released which can cause injury.

• To reduce the risk of fire or personal injury, use only the

battery listed in the User’s Guide.

• Keep batteries out of the reach of children.

• Remove batteries if storing over 30 days.

NOTE: The RBRC seal on the battery

used in your ATLINKS USA product

indicates that we are participating in a

program to collect and recycle Nickel

Cadmium batteries throughout the United

States. Please call 1-800-8-BATTERY for information or

contact your local recycling center.

GENERAL PRODUCT CARE

To keep your telephone working and looking good, follow

these guidelines:

• Avoid putting the phone near heating appliances and

devices that generate electrical noise (for example,

motors or fluorescent lamps).

• DO NOT expose to direct sunlight or moisture.

• Avoid dropping the handset, as well as other rough

treatment to the phone.

• Clean the phone with a soft cloth.

• Never use a strong cleaning agent or abrasive powder

because this will damage the finish.

• Retain the original packaging in case you need to ship

the phone at a later date.

• Periodically clean the charge contacts on the handset

and base with a clean pencil eraser.

TROUBLESHOOTING TIPS

CALLER ID

Problem Solution

No Display • Is battery fully charged?

Try replacing the battery.

• If you are using AC power,

make sure that the unit is

connected to a non-

switched electrical outlet.

Disconnect the unit from

the plug and plug it in

again.

• Did you order Caller ID

service from your local

telephone company?

Caller ID Error Message • The unit displays this

message if it detects

anything other than valid

Caller ID information

during the silent period

after the first ring. This

message indicates the

presence of noise on the

line.

TELEPHONE

Problem Solution

No dial tone • Check installation:

— Is the base power cord

connected to a working

outlet?

— Is the telephone line cord

connected to the base unit

and the wall jack?

• Disconnect the base from

the wall jack and connect

another phone to the same

jack. If there is no dial tone

in the second phone, the

problem might be your

wiring or local service.

• Is the handset out of range

of the base?

• Make sure the battery is

properly charged (12

hours).

• Is the battery pack

installed correctly?

• Did the handset beep

when you pressed the

TALK button? Did the

CHARGE/ IN USE indicator

come on? The battery may

need to be charged.

Dial tone is OK, but • Make sure the tone/

can't dial out pulse setting is

programmed

correctly.

Handset does not ring • Make sure the RINGER

switch on the handset is

turned to ON.

• You may have too many

extension phones on your

line. Try unplugging some

phones.

• See solutions for “No dial

tone.”

ACCESSORY ORDER FORM

(OR CALL 1-800-338-0376 FOR ACCESSORIES ONLY)

CUSTOMER: CUT ALONG DOTTED LINE.

✂

*Prices are subject to change without notice.

Total Merchandise.........................................$_______________

Sales Tax........................................................$_______________

We are required by law to collect the appropriate sales tax for each individual state,

county, and locality to which the merchandise is being sent. Duties will apply for

shipments to Canada.

Use VISA or Master Card or Discover preferably. Money order or check must be in U.S.

currency only. No COD or Cash. All accessories are subject to availability. Where

applicable, we will ship a superseding model.

Shipping/Handling....................................... $_______________

Total Amount Enclosed.................................$_______________

Mail order form and money order or check (in U.S. currency)

made payable to Thomson Consumer Electronics, Inc. to:

TCE

Mail Order Department

P.O. Box 8419

Ronks, PA 17573-8419

Name_______________________________________________________

Address_____________________________________ Apt.____________

City ________________________State________ ZIP_________________

Daytime Phone Number ( )_______________________________

Please make sure that this form has been filled out completely.

____________________________________________________________________

Authorized Signature

My card expires:

Copy the number above your

name on the Master Card

For credit card purchases

Your complete charge card number, its expiration date and your

signature are necessary to process all charge card orders.

Copy your complete account number from your VISA card.

My card expires:

Copy your complete account number from your

Master Card or Discover.

$5.00

HEADSET

Headset

jack

Headset

plug

Slot for

belt clip

Slot for

belt clip

DESCRIPTION

CATALOG NO.

TOTAL

QTY.

PRICE*

Belt clip

5-2462

$4.95

Headset

5-2425

$36.35

5-2461

$14.95

Replacement battery

5-2463

5-2444

(white)

(black)

SETTING THE LCD CONTRAST

1. Press the MENU button. The display shows

1-SET

CONTRAST

2. Use the arrow buttons to increase or decrease the

contrast.

3. The default setting is 2.

4. Press the MENU button again to save the selection and

proceed to the next step.

SETTING THE RINGER ON/OFF

1. The display shows

2-SET RINGER.

2. Use the arrow buttons to turn the ringer ON or OFF. The

ringer icon will not display if the ringer is OFF.

3. Press the MENU button again to save the selection and

proceed to the next step.

SETTING THE TIME/DATE

1. The display shows

3-SET TIME

2. The first digit for the month will begin to blink.

3. Use the arrow buttons to increase or decrease the

month.

4. Press DELETE to set the date.

5. The first digit for the day will begin to blink.

6. Use the arrow buttons to increase or decrease the day.

7. Press DELETE again to set the time. The hour “12” will

start blinking.

8. Use the arrow buttons to increase or decrease the hour.

9. Press DELETE again to set the minute. The minute “00”

will start blinking.

10.Use the arrow buttons to increase or decrease the

minute.

11.Press the MENU button again to save the selection and

proceed to the next step.

NOTE: The time and date will be automatically saved

to the Caller ID box if an incoming call with Caller ID

information is received.

SETTING THE TEMPERATURE

DISPLAY °C/F

1. The display shows

4 - SET TEMP

. The default

setting is ˚F.

2. Use the arrow buttons to change from ˚C and ˚F.

3. Press the MENU button again to save the selection and

return to stand-by mode.

DISPLAY IN STANDBY

When not in use, the display shows the date, time, room

temperature and total number of new calls.

DISPLAY DURING RINGING

• If the remote Caller ID box is operating on battery

power, the display will only show information when a

Caller ID call comes in.

• While in standby mode, if no caller ID message is

received during an incoming call, the display shows

DATA

• Caller ID information will be displayed for several

seconds after a call is received.

DISPLAY IN ON STATE

• If the remote caller ID box is plugged into an AC outlet,

the display waits for Caller ID data from the base.

• The Caller ID display format will be the same as the

Caller ID received during ringing.

CAUSES OF POOR RECEPTION

• Aluminum siding

• Foil backing on insulation

• Heating ducts and other metal construction can shield

radio signals

• You’re too close to appliances such as microwaves,

stoves, computers, etc.

• Atmospheric conditions, such as strong storms

• Base is installed in the basement or lower floor of the

house

• Base is plugged into an AC outlet with other electronic

devices

• Baby monitor is using the same frequency

• Handset battery is low.

• You’re out of range of the base.

MESSAGE INDICATORS

The following indicators show the status of a

message or of the unit.

ERROR Caller information has been interrupted

during transmission or the phone is

excessively noisy.

ENTER NAME Prompt telling you to enter a name for

one of the 10 memory locations.

ERASE ALL? Prompt asking if you want to erase all

Caller ID records.

ERASE CALL ID? Prompt asking if you want to erase the

current Caller ID record that is shown

on the display.

ERASE MEMO? Prompt asking if you want to erase one

of the 10 numbers stored in the

phone's outgoing memory.

END OF LIST Indicates there is no additional

information in the Caller ID memory

log.

NEW Indicates call or calls have not been

reviewed.

UNKNOWN The incoming call is from an area not

serviced by Caller ID or the information

was not sent.

PAGING YOU Someone has pressed the PAGE button

on the base.

BLOCKED The person is calling from a number

that has been blocked from

transmission.

REPT Repeat call message. Indicates that a

new call from the same number was

received more than once.

NO DATA No Caller ID information was received.

MEMO Memo record is being displayed on

the handset.

CALL Caller ID record is being displayed on

the handset.

# Indicates a memory record number.

AM Indicates the time is morning.

PM Indicates the time is afternoon.

You experience static, • Change channels

noise, or fading in • Is handset out of range?

and out Move closer to the base.

• Does the base need to be

relocated?

• Charge battery.

• Make sure base is not

plugged into an outlet with

another household

appliance.

Unit beeps • Place handset in base for

20 seconds to reset the

security code. If that

doesn’t work, charge

battery for 12 hours.

• Clean charging contacts on

handset and base with a

soft cloth, or an eraser.

• See solutions for “No dial

tone.”

• Replace battery.

Memory Dialing • Did you program the

memory location keys

correctly?

• Did you follow proper

dialing sequence?

• Make sure the tone/pulse

setting is programmed

correctly.

• Did you reprogram

numbers into memory

after power outage or

battery replacement?

ANDSET

ALLER

ID B

OUND

IGNALS

Signal Meaning

A long warbling tone Signals an incoming call

(with ringer on)

One short beep, one Page signal

long beep (several times)

One short beep Key beep signal

Three short beeps Error signal

Four short beeps Low battery warning

Two long beeps Confirmation tone

SERVICE

The FCC requires this product to be serviced only by the

manufacturer or its authorized service agents. In

accordance with FCC requirements, changes or

modifications not expressly approved by ATLINKS USA

could void the user’s authority to operate this product. For

instructions on how to obtain service, refer to the warranty

included in this user's guide or contact Consumer

Information at 1-800-448-0329.

Attach your sales receipt to the booklet for future reference

or jot down the date this product was purchased or

received as a gift. This information will be valuable if

service should be required during the warranty period.

Purchase date__________ Name of store__________________

INTERFERENCE INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference; and (2) This device must accept any

interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna (that is, the antenna

for radio or television that is “receiving” the interference).

• Reorient or relocate and increase the separation between the

telecommunications equipment and receiving antenna.

• Connect the telecommunications equipment into an outlet on a

circuit different from that to which the receiving antenna is

connected.

• Consult the dealer or an experienced radio/TV technician for

help.

If these measures do not eliminate the interference, please consult

your dealer or an experienced radio/television technician for

additional suggestions. Also, the Federal Communications

Commission has prepared a helpful booklet, “How To Identify and

Resolve Radio/TV Interference Problems.” This booklet is available

from the U.S. Government Printing Office, Washington, D.C. 20402.

Please specify stock number 004-000-00345-4 when ordering

copies.

LIMITED WARRANTY

What your warranty covers:

• Any defect in materials or workmanship.

For how long after your purchase:

• One year.

(The warranty period for rental units begins with the first rental

or 45 days from date of shipment to the rental firm, whichever

comes first.)

What we will do:

• Provide you with a new or, at our option, a refurbished unit.

• The exchange unit is under warranty for the remainder of the

original product’s warranty period.

How to make a warranty claim:

• Properly pack your unit. Include any cables, etc., which were

originally provided with the product. We recommend using the

original carton and packing materials.

• Include evidence of purchase date such as the bill of sale. Also

print your name and address and a description of the defect.

Send via standard UPS or its equivalent to:

Thomson Consumer Electronics, Inc.

11721 B Alameda Ave.

Socorro, Texas 79927

• Pay any charges billed to you by the Exchange Center for

service not covered by the warranty.

• Insure your shipment for loss or damage. Thomson accepts no

liability in case of damage or loss en route to Thomson.

• A new or refurbished unit will be shipped to you freight

prepaid.

What your warranty

does not

cover:

• Customer instruction. (Your Owner’s Manual provides

information regarding operating instructions and user controls.

For additional information, ask your dealer.)

• Installation and set-up service adjustments.

• Batteries.

• Damage from misuse or neglect.

• Products which have been modified or incorporated into other

products.

• Products purchased or serviced outside the USA.

• Acts of nature, such as but not limited to lightning damage.

Product Registration:

• Please complete and mail the Product Registration Card packed

with your unit. It will make it easier to contact you should it

ever be necessary. The return of the card is not required for

warranty coverage.

How state law relates to this warranty:

• This warranty gives you specific legal rights, and you may have

other rights which vary from state to state.

If you purchased your product outside the USA:

• This warranty does not apply. Contact your dealer for warranty

information.

317-555-4231

DATE

12/31

TIME

12:20

CALL

GEORGE ANDERSON

NEW

82.3F

CALL

NEW

12/30 12:25

TIME MODE CALLER ID MODE

Review

REVIEW buttons

MENU button

DELETE button

1 2

Commentaires sur ces manuels

Pas de commentaire

Ge 26995 Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Téléphone sans fil à combiné Ge 26995