Ge Profile Advantium JX2201NSS Manuel d'utilisateur télécharger pdf (Page 2)

Specification Created 11/08

240446

Listed by

Underwriters

Laboratories

PSB1201NSS

GE Profile Advantium

120 Volt - 30" Wall Oven

Installation over a GE/Monogram

Warming Drawer:

30”

23-1/2”

25-1/4”

Min.

21”

2” Min.

(3” recommended)

Per warming

drawer

requirement

Construct

Solid Bottom

Min. 3/8”

Plywood

Supported

by 2x4 or 2x2

Runners all

Four Sides

5” min.

from ﬂoor

1” min.

above

toekick

Warming Drawer:

Construct Solid

Bottom Min.

3/8” Plywood

Supported by

2x4 or 2x2

Runners all

Four Sides

30”

23-1/2”

21”

2” Min.

Per Oven

Requirement

Per warming drawer requirement

2” Min.

(3” recommended)

25-1/4”

Min.

5” min.

from ﬂoor

1” min.

above

toekick

Prepare the opening (cont.)

When installed over a single oven or a

warming drawer, allow at least 2" between

the two openings. This separation will

provide clearance for bottom overlap of the

Advantium and the other appliance overlaps.

Construct a solid oven floor of 3/8" min. thick

plywood supported by 2 x 4 or 2 x 2 runners

on all sides.

• the support must be level and rigidly

mounted, flush with the bottom edge of

the cutout.

Note: Additional clearances between the

cutouts may be required. Check to be sure the

oven supports above the Warming Drawer

location do not obstruct the required interior

depth and height. See Warming Drawer

installation instructions for details.

Installation over a GE/Monogram Oven

and Warming Drawer:

Note: Additional clearances between the

cutouts may be required. Check to be sure the

oven supports above the Warming Drawer

location do not obstruct the required interior

depth and height. See Warming Drawer

installation instructions for details.

CAUTION: For personal safety, the mounting

surface must be capable of supporting the

cabinet load, in addition to the added weight

of this approximate 80-pound oven and 30-

pound drawer, plus additional oven loads of up

to 50 pounds or a total weight of 160 pounds.

Preparation WITH an Accessory Drawer

Prepare the opening

The Advantium PSB1200/1 series can be installed in combination with

other GE/Monogram appliances. Always follow each product's Installation

Instructions to compete the installation.

Single Oven Installation:

Order a 30" wide single oven cabinet or cut the opening in a wall to the

dimensions shown.

* For existing cutouts, a maximum

width of 28-1/2" is acceptable. If

the opening is slightly wider, secure

a furring strip on each side of the

cutout for securing the oven.

• Allow 3/4" to 2-1/8" case trim overlap

on the sides and 7/8" overlap on the

bottom of the opening for all models.

The amount of overlap on the sides

depends on the actual cutout width.

Allow 1-1/4" case trim overlap on the

top for models PSB1200 and PSB1201

and for models ZSC1201 and ZSC1202.

• Oven overlaps will conceal cut edges on all sides of the opening.

Note: PSB1200/1 series Advantium can be installed below GE/GE Profile

non-downdraft gas and electric cooktops. It CANNOT be installed below

induction or Monogram (2GU3841385) gas cooktops.

Note: PSB1200/1 series Advantium oven comes with two lower trim

pieces. One is for use above 36-inch height installations and one is for

use below 36-inch installations. Use of the accessory drawer will replace

the bottom trim piece for applicable installations. Please see installation

instructions for full details.

30”

23-1/2”

25-1/4”

Min.

21”

Construct

Base

Min. 3/8”

Plywood

Supported

by 2x4 or 2x2

Runners all

Four Sides

5” min.

from ﬂoor

1” min.

above

toekick

For answers to your Monogram,

GE Profile

™

or GE

appliance questions, visit our website at ge.com or

call GE Answer Center

service, 800.626.2000.

1 2 3

PSB1201NSS 1
GE Profile Advantium 3

Commentaires sur ces manuels

Pas de commentaire

Ge Profile Advantium JX2201NSS Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Four Ge Profile Advantium JX2201NSS