GE RV60 Guide d'installation télécharger pdf

imagination at work

Lighting

OEM Installation Guide

• Installation to be performed by factory trained service

personnel only.

• For use inside a commercial refrigeration case with packaged

foods only.

• Use this unit only in the manner intended by the manufacturer.

If you have any questions, contact the manufacturer.

• Before installing, servicing or cleaning unit, switch power off

at the service panel and follow appropriate lock out/tag out

safety procedures

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS shown

throughout these instructions.

LED DRIVER COMPATIBILITY

This system is compatible with GEPS6000NCMUL-SY or

GEPS6500NCMUL-SY LED Driver. Please refer to the separate

LED driver installation guide for appropriate wiring connections.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

CAUTION/ATTENTION

Risk of injury. While performing installations described, gloves, safety

glasses or goggles should be worn. / Risque de blessure. Lors de

l'exécution des installations décrites, des gants, des lunettes de sécurité

ou des lunettes de protection doivent être portées.

WARNING/

AVERTISSEMENT

Risk of electrical shock. Disconnect power before servicing or

installing product. / Risque de choc électrique. Couper le courant

avant de réparer ou installer le produit.

• The power supply must be supplied with 100-240 VAC,

50/60 Hz, and connected to an individual properly grounded

branch circuit, protected by a 15 or 20 ampere circuit breaker

or time delay fuse.

• Wiring must be 2 wire with ground and rated for 75°C (167°F).

• Do not overload driver, follow installation instructions for the

GEPS6000NCMUL-SY or GEPS6500NCMUL-SY.

• Ensure that all connection points are sealed for damp location

using the appropriate method per the NEC or local electrical code.

PREPARE ELECTRICAL WIRING

Electrical Requirements

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

IMMERSION

LED Refrigerated Display Lighting

Vertical Cases

RV60 Series

End Mullion Lights

48-inch: GELT604850EDR-SY/-SB (85743/85746), GELT604850EDL-SY/-SB (85744/85747), GELT604840EDR-SY/-SB (85749/85752),

GELT604840EDL-SY/-SB (85750/85753), GELT604835EDR-SY/-SB (85755/85758), GELT604835EDL-SY/-SB (85756/85759)

60-inch: GELT606050EDR-SY/-SB (85700/85703), GELT606050EDL-SY/-SB (85701/85704), GELT606040EDR-SY/-SB (85706/85709),

GELT606040EDL-SY/-SB (85707/85710), GELT606035EDR-SY/-SB (85712/85715), GELT606035EDL-SY/-SB (85713/85716)

67-inch: GELT606750EDR-SY/-SB (85720/85723), GELT606750EDL-SY/-SB (85721/85724), GELT606740EDR-SY/-SB (85726/85734),

GELT606740EDL-SY/-SB (85727/85735), GELT606735EDR-SY/-SB (85737/85740), GELT606735EDL-SY/-SB (85738/85741)

Description Code (Single Unit Product Number/10-Pack Product Number)

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - IMMERSION

imagination at workGE LightingOEM Installation Guide• Installation to be performed by factory trained service personnel only.• For use inside a c

Page 2 - End LED Lights

Wire stripper/cutterTape measureScrewdriverCordless drillHammer7/64-inch (2.8mm) drill bitCenter punch1231234LED lightLED driverWire cover6-32 x 1/2&q

Page 3 - Right from Left

Install End LED Lights2• Place proper End LED Light against the face of the mullion near the two holes drilled at the top. NOTE: Refer to proper

Page 4 - Maximum LED Driver Loading

4CAUTION/ATTENTIONRisk of injury. Do not overload LED Driver. Do not exceed limits shown in “Maximum LED Driver Loading” table below. Risque de blessu

Page 5 - Connection Congurations

Connection Congurations3For information on A, B, C, D, see Steps 4, 5 and 6.WARNING/AVERTISSEMENTRisk of electrical shock. Ensure that all connection

Page 6 - Connect LED Driver - Input

6• Make output (DC) connections using one of the two options below:Connect LED Driver - OutputOPTION 1 – USING 4-WAY CONNECTOR OPTION 2 – USING TWIST-

Page 7 - Removal Instructions

• Tuck wires underneath Wire Cover before placing it over the End Cap and Mounting Tab.• Attach Wire Cover to LED Light End Cap by installing a M2

Page 8 - WARNING/AVERTISSEMENT

• The outer lens and the plastic housing should be cleaned periodically with a mild liquid dish detergent.• Do not use chemical cleaners to clean t