GE SAM Guide d'installation télécharger pdf

GEH-5953A

INSTRUCTIONS

Type 201 SA

(For Non UL and UL Listed Fixtures)

READ THOROUGHLY BEFORE INSTALLING

CAUTION: Type 201 SA luminaire is designed for

outdoor lighting and should not be used in areas of

limited ventilation, or in high ambient temperature

enclosures.

STEP 1 (FOR NON UL LISTED FIXTURES)

Installation of mounting arm to pole

Type 201 SA luminaire, unit pack, is designed for mounting

on a round wood pole. (See above illustration for identifica-

tion and location of parts.) The mounting arm should first

be mounted to pole. A clearance hole for a 5/8-inch

diameter bolt must be drilled through pole. The 10-inch

through bolt should be inserted through clearance hole and

2-inch square washer and nut screwed loosely onto opposite

end of through bolt. The pole plate on mounting arm should

be placed over square head of through bolt so that square

head is engaged by two indented tabs on pole plate.

(See illustration A).

STEP 1 (TYPE 201 SA CONDUIT MOUNTING)

(FOR UL LISTED FIXTURES)

Installation of mounting arm to pole

NOTE: This fixture is intended to be conduit con-

nected to a properly installed and properly grounded

weatherproof junction box (not provided). All conduit

connectors, conduit and junction boxes (not pro-

vided) should be UL listed suitable for wet locations.

Attach two-piece mounting brackets to extension arm by

interlocking bracket and securing with ¼ -20 carriage bolt

and ¼ -20 hex nut provided. Mounting bracket should be

secure leaving approximately one inch of extension arm

protruding from bottom of bracket as shown. Place extension

arm assembly onto desired mounting surface and mark four

hole locations required mounting. Remove arm assembly

and drill four marked locations for ease of mounting. Mount

extension arm assembly using hex head lag bolts provided.

Tighten bolts securely before proceeding.

STEP 2

Installation of hood to mounting arm

Type 201SA

Conduit

Mounting

(For Non-UL

Listed

Fixtures)

CAUTION

Unit will fall if not installed properly

• Follow installation instructions

WARNING

Risk of electric shock

• Turn power off before servicing

– see instructions

The leads from hood should first be inserted through

outboard end of the mounting arm and brought out through

inboard end adjacent to the pole plate.

(For Non UL fixtures, it is recommended a drip loop be

formed where leads exit mounting arm as indicated in above

drawing.)

ILLUSTRATION A

Nut should be tightened down so that mounting arm is

securely attached to pole. Lag bolts should be inserted into

outside lower holes of mounting arm pole plate. Hammer lag

bolts in to within approximately 1” of head, then tighten

down with wrench.

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or

maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the matter should be referred

to GE Lighting Solutions.

Lighting Solutions

1 2 3 4

Type 201 SA 1
ATTENTION 3

Résumé du contenu

Page 1 - Type 201 SA

GEH-5953AINSTRUCTIONSType 201 SA(For Non UL and UL Listed Fixtures)READ THOROUGHLY BEFORE INSTALLINGCAUTION: Type 201 SA luminaire is designed foroutd

Page 2

For all fixtures, check to see if opening of mounting armclamp in slipfitter is large enough to allow mounting arm tobe inserted. If not, loosen two c

Page 3 - ATTENTION

GEH-5953AINSTRUCTIONSType 201 SA(Luminaires catalogués UL ou non)À LIRE ATTENTIVEMENT AVANT D’INSTALLERATTENTION : Le luminaire de type 201 SA a été c

Page 4

35-201578-146 (6/06)Pour tous les appareils, vérifier que l’ouverture de l’étrierpour bras de montage de l’adaptateur d’emboîtement est assezlarge pou

Plus de documents pour Non GE SAM

GE SAM Fiche technique (2 pages)

Voir le document GE SAM Guide d'installation

GE SAM Guide d'installation (2 pages)

Commentaires sur ces manuels

Pas de commentaire

Ihome IP28 Manuel de l'utilisateur (12 pages)

marque: Ihome | Catégorie: Alarm clocks | Taille: 0.27 MB |

Table des matières

Model iP28

The Portable Speaker System

For Your iPhone & iPod

Table of Contents

Maintenance

FCC Information

Use this insert

For this iPhone/iPod

Controls and Indicators

Back of Unit

Setting Up the iP28

Setting the Clock

Using the Alarm

Using the iP28

Using Sleep Mode

Using Dimmer

Using the Line-in Jack

Using the Travel Lock

Using the EXB sound

Troubleshooting

Printed in China

Plus de produits et de manuels pour Réveils IHome

Modèles	Type de document
ZN90	Manuel de l'utilisateur iHome ZN90 User's Manual, 12 pages
iH16	Manuel de l'utilisateur iHome iH16 User's Manual, 14 pages
ZN9	Manuel de l'utilisateur iHome ZN9 User's Manual, 12 pages
iH18	Manuel de l'utilisateur iHome iH18 User's Manual, 16 pages
iH55	Manuel de l'utilisateur iHome iH55 User's Manual, 14 pages
iHC5	Manuel de l'utilisateur iHome iHC5 User's Manual, 17 pages
iH51	Manuel de l'utilisateur iHome iH51 User's Manual, 17 pages
iH6	Manuel de l'utilisateur iHome iH6 User's Manual, 13 pages
iH3	Manuel de l'utilisateur iHome iH3 User's Manual, 13 pages
iBN180	Manuel de l'utilisateur iHome iBN180 User's Manual, 19 pages
IBN20	Manuel d'instructions iHome IBN20, 20 pages
IDL45B	Instructions d'exploitation iHome iDL45, 13 pages
iP16	Manuel d'instructions iHome iP16 [de] [fr] [it] [ja] [ko] [pl] [tr] , 8 pages
iP23	Manuel d'instructions iHome iP23, 12 pages
IP41	Instructions d'exploitation iHome iP41, 11 pages
iK50	Manuel d'instructions iHome iK50, 16 pages
IP48	Instructions d'exploitation iHome IP48, 12 pages

GE SAM Guide d'installation