GE GTW460ASJWW Manuel d'installation télécharger pdf (Page 19)

Save time and money! Review the charts on the following pages, or visit GEAppliances.com. You may not need to call for service.

Before you call for service…Troubleshooting Tips

WATER Possible Causes What To Do

Small amount of water

remaining in dispenser

(on some models) at

end of cycle

Normal dispenser

operation

It is normal for a small amount of water to remain in dispenser after the

cycle.

Short spray and delay

after pushing the Start

button

Lid was opened and closed

between cycle selection

and start

This is normal. See START-UP SEQUENCE in the Safety Instructions

section.

Water level seems low This is normal Water may not cover the top level of the clothes. This is normal for this

high efficiency washer.

Low water flow Water valve screens are

stopped up

Turn off the water source and remove the water connection hoses from

the upper back of the washer and the water faucets. Clean both the

hose screens (if so equipped) and the screens in the machine using a

brush or a toothpick. Reconnect the hoses and turn the water back on.

Check to ensure there are no leaks at the connections.

Water siphoning out

of washer

Drain standpipe is too

low or hose too far into

standpipe

The drain hose must exceed 32” height at some point between

the washer back and the drain pipe. Use anti-siphon clip. See the

Installation Instructions.

Too many suds Soft water Try less detergent.

Too much detergent Measure your detergent carefully. Use less soap if you have soft water, a

smaller load or a lightly soiled load.

Type of detergent

Switch to High Efficiency detergent such as .

Water leaks Type of detergent

Switch to High Efficiency detergent such as .

Using too much detergent

in washer

Use less detergent. Use less soap if you have soft water, a smaller load

or a lightly soiled load.

Fill hoses or drain hose is

improperly connected

Make sure hose connections are tight at faucets and rubber washers

are installed. Make sure end of drain hose is correctly inserted in and

secured to drain facility.

Household drain clogged Check household plumbing. You may need to call a plumber.

Drain hose rubs on wall Make sure drain hose does not make contact with the wall. May cause

excessive wear on the hose.

Constant water pressure to

fill hoses at water source

Tighten hoses at the faucets.

Check condition of the fill hoses; they should be replaced every 5 years.

Water temperature

seems incorrect

Cooler water temperatures

provide improved energy

efficiency

New laundry detergents have been formulated to work with cooler

water temperatures without affecting wash performance.

Water supply is turned off

or improperly connected

Turn both hot and cold faucets fully on and make sure hoses are

connected to correct faucets. NOTE: Water valves are marked “H” and “C”.

Water valve screens are

stopped up

Turn off the water source and remove the water connection hoses from

the upper back of the washer and the water faucets. Clean both the

hose screens (if so equipped) and the screens in the machine using a

brush or a toothpick. Reconnect the hoses and turn the water back on.

Check to ensure there are no leaks at the connections.

Cool/Cold Water when

selecting Hot

This is normal. The washer senses water temperature (on some models)

and optimizes for best results. Cold water is added periodically when hot

is selected.

House water heater is not

set properly

Make sure house water heater is delivering water at 120°F–140°F

(48°C–60°C).

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 79 80

Commentaires sur ces manuels

Pas de commentaire

GE GTW460ASJWW Manuel d'installation Page 19

Commentaires sur ces manuels

Produits connexes et manuels pour Machines à laver GE GTW460ASJWW