GE PT920 Manuel d'utilisateur télécharger pdf (Page 24)

ge.com

27" built-in single ovens (continued)

Undercounter installation dimensions (in inches)

Models PK916, JKP70, JKP30 and JKS10

Gas or electric cooktops may be installed over this

oven. See cooktop installation instructions for cutout size.

See label on top of oven for approved cooktop models.

Gas or electric connections

for gas cooktop must be

located in an adjacent

accessible location to the right

240V / 208V

Junction Box

Location

36"

Typical

Countertop

Height

Allow 1"

unit overlap

all edges

25" MIN.

25 1/4" MAX.

27 5/8" MIN.

28 1/8" MAX.

3/4" Support

Platform Required

Must Support 150 Lbs.

22" MIN.

Above

Support

Platform

Note: Oven is rated for use only under 30" standard or sealed burner gas and

selected 30" CleanDesign and Calrod

electric cooktops.

Installation information: Before installing, consult installation instructions

packed with product for current dimensional data.

27"/24" built-in single oven dimensions (in inches)

27" models PK916, JKP70, JKP30, JKS10

2" x 4"

or equiv.

runners

B MIN.

C MIN.

Conduit 48-1/2" long

32-1/2

Allow 3/4"

for overlap

over all edges

of cutout

Locate

junction box

either 5" MIN.

below cutout

floor or 44"

MIN. above

cutout floor

Minimum

cutout location

from floor

(Minimum 15-5/8"

from floor when

installed below built-in

microwave oven)

Sealed burner gas cooktop

installation dimensions (in inches)

Standard burner gas cooktop

installation dimensions (in inches)

90° Street el

45° Elbow

Cabinet sides

2" Diameter hole (20-7/8"

from front of countertop

to hole center)

5" To center of 2" diameter

hole from countertop

90° Street el

45° Elbow

To center of 2" diamete

hole from countertop

Cabinet sides

3-7/16"

2" MIN. diameter hole

(23-1/4" from front

surface of countertop)

Note: Cabinets installed adjacent to wall ovens must have

an adhesion spec of at least a 194°F temperature rating.

Note: These ovens are not approved for stackable or side-by-side installations.

Note: Door handle protrudes 3" from door face. Cabinets and drawers on adjacent

45° and 90° walls should be placed to avoid interference with the handle.

Note: Cabinets installed adjacent to wall ovens must have an adhesion spec of at

least a 194°F temperature rating.

Note: For 27" built-in single ovens, if marks, blemishes or the cutout opening is

visible above the installed oven, it may be necessary to add wood shims under the

runners and front trim until the marks or openings are covered.

Electric wall ovens are not approved for installation with a plug and receptacle.

They must be hard wired in accordance with installation instructions.

Note: 36" ribbon cooktops are approved for use over

GE 30" single wall ovens* and warming drawers. 30"

ribbon cooktops are approved for use over GE 30"

and GE 27" single wall ovens* and warming drawers.

Refer to cooktop and wall oven installation information

packed with products for current dimensional data.

*Except wall ovens with Trivection

technology.

Oven support

for 27" models

Oven support

for 24" models

Suitable

bracing

to support

runners

18"

Over centerline

of cabinet

2" x 4" or

equivalent

runners

(Must support 275 lbs.)

2 x 4 or

equivalent

runners

11"

over centerline

of cabinet

Cabinet PK916, JKP70/30, JKS10

A – Cabinet width required 27" min.

B – Minimum cabinet depth 23-5/8"

C – Opening width 25" min. - 25-1/4" max.

D – Opening height 27-5/8" min. - 28-1/8" max.

Oven

E – Overall depth* 23-5/8"

w/o trim 29"

F – Overall height with trim 29-7/8" - 30-3/4"

G – Overall width 26-5/8"

* Depth including door handle is approximately 26-7/8" min to

26-8/10" max. 26-5/8" on models PK916, JKP70/30 and JKS10.

47019_GE_59 5947019_GE_59 59 2/6/07 4:34:18 PM2/6/07 4:34:18 PM

1 2 ... 19 20 21 22 23 24

Commentaires sur ces manuels

Pas de commentaire

GE PT920 Manuel d'utilisateur Page 24

Commentaires sur ces manuels

Produits connexes et manuels pour Fours GE PT920