GE JKP44GP Manuel d'utilisateur télécharger pdf (Page 19)

Operating the Self-Cleaning Oven

Set the Oven for Cleaning

If range is too hot and you start to

set a clean cycle, the word “OFF”

will appear in the display. Allow

additional time for cooling before

you try to set the cycle.

NOTE: Only one oven at a time

can be self-cleaned.

“OFF”

wiH

appear in the display if you try to

clean both ovens at the same time.

1. Close the oven door

compl.etel.y.

2. Touch the CLEAN pad.

3. Touch INCREASE or

DECREASE pad.

“3:00,”

“HJ?”

and “TIME CLEAN” will appear

on display. Three hours is the

programmed clean time, but

any

time between two and four hours

can be set.

The door latches automatically.

If the oven door is not closed, the

word “DOOR” is displayed, the

word “LOCK” will flash

ad

the

oven will signal. Close the door.

The signal will stop and the

clean.

cycle will start when the door

can lock.

When a clean cycle is finished, the

word “CLEAN” will be off

in the display.

You

will

not

be able to open the

door unless the oven temperature

i.s

at a safe level, when “LOCK”

goes out on display. Wait until the

oven

has cooled. below locking

temperature (about 20-30 minutes).

NOTE: You can

fj.nd

out when the

clean cycle

will.

be finished by

~u~h,i,n,g

the STOP

THv!E

pad.

TO

Set a Delayed Start

1.

Close

the

oven.

door

com.pl.etely.

2.

Touch

the CLEAN pad.

3.

Touch. INCREASE

or

DECREASE pad to enter

CJ.ean

Time.

4. Touch STOP

TIME pad. “SET

STOP TIME” and. the

ear].iest

stop

time you can set

will

appear

on

djsplay.

The ea~l.j.est

stop

tjrne

will

be

the

clean

tj.m.e

selected. plus the

tjrne

of

da.~.

For

example:

j.~

the

clean tj.rne

is

t~.ree

hOIJM

and

the

time

of

day

is

6:00,

the

stop

time

that appears

on

di.spl.ay

will. be

9:00.

5.

~OUCb

INCREASE pad. to

change

the

stop

tjme

02

a. later tkne

of

clay

if

desir~d.

For example: if

you

set.

stop

tkne

at

1.1

:00,

oven

will

start

cl”em

cycle

a.t

8:()()

and

end a.t 1.1.:00.

NOTE:

During a. delayed

sel.f-

cl.ean

operation you. can find out

when

the oven is set to

tu..m

on

by

p~lshing

and. holding the

CJ_EAN

pad for

3

seconds.

To

Stop a

Clean.

Cycle

1.

Press the

CLEAIUOFF

pad.

After Self-Cleaning

You may notice some white ash

in the oven.

Just wipe it up with.

a damp

cloth

after the oven cools.

If white spots remain, remove

them with a soap-filled steel wool

pad. Be sure to

rhse

thoroughly

with a vinegar and water mixture.

These

deposits are usually a salt

residue that

carmot

be removed

by the clean cycle.

If the oven is not clean after one

clean cycle, repeat the cycle.

NOTE: A Bake or

Broil function

cannot be programmed before the

door

autornaticall.y

unlocks.

If “F-” and a number flash

on display and the control

beeps, this indicates function

error code.

Press

CLEAIVOFF

pad.

Allow oven to cool for one

hour. Put oven back into

operation. If function error

code repeats, disconnect power

to the oven and call for service.

(continued next page)

19

1 2 ... 14 15 16 17 18 19 20 21 22 23 24

Commentaires sur ces manuels

Pas de commentaire