GE DCVH680EJBB Manuel d'utilisateur télécharger pdf

Questions or Installation? Call: 1-800-GECARES (US)

or Visit our Web site at: www.GEAppliances.com (US)

Installation

Instructions

Electric Dryer

Step 1 Prepare the Area and Exhaust for Installation of New

Dryer (see section 1).

Step 2 Check and Ensure the Existing External Exhaust is

Clean (see section 1) and Meets Attached Installation

Specifications (see section 3).

Step 3 Remove the Foam Shipping Pads (see section 1).

Step 4 Move the Dryer to the Desired Location.

Step 5 Connect the Power Supply (see section 2).

Step 6 Connect the External Exhaust (see section 4).

Step 7 Level Your Dryer (see section 5).

Step 8 Check the Operation of the Power Supply and

Venting.

Step 9 Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be

Noticed By the Owner.

For Alcove or Closet Installation, see section 6.

For Bathroom or Bedroom Installation, see se

ction 7.

For Mobile or Manufactured Home see, section 8.

For side or bottom exhaust, see section 9.

500A436P009_Rev0 Pub # 31-16228

PEDESTALS FOR DRYERS

(comes with individual installation instructions)

Three models available: - SBSD227F

- SBSD137H- SBSD107H

NOTE: Installation and service of this dryer

requires basic mechanical and electrical skills.

It is your responsibility to contact a qualified

installer to make the electrical connections.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT-

Save these instructions for local

inspector’s use.

•

IMPORTANT-

Observe all governing codes and

ordinances.

• Note to Installer - Be sure to leave these instructions with

the customer.

•

Note to Customer

- Keep these instructions with your Use

and Care Book for future reference.

• Before the old dryer is removed from service or discarded,

remove the dryer door.

• Service information and the wiring diagram are located in

the control console.

• Do not allow children on or in the appliance. Close super-

vision of children is necessary when the appliance is used

near children.

•

Install the dryer where the temperature is above 50°F for

satisfactory operation of the dryer control system.

MATERIALS YOU WILL NEED

GLOVES

SAFETY

GLASSES

DRYER POWER CORD

KIT (NOT PROVIDED

WITH DRYER)

4" DUCT

CLAMPS (2)

4" SPRING

CLAMPS (2)

EXHAUST

HOOD

3/4" STRAIN

RELIEF

UL RECOGNIZED

4" DIA. METAL

ELBOW

4" DIA. FLEXIBLE METAL (SEMI-RIGID)

UL LISTED TRANSITION DUCT

(IF NEEDED)

KIT WX08X10077 (INCLUDES 2 ELBOWS)

4" DIA. METAL DUCT

(RECOMMENDED)

4" DIA. FLEXIBLE METAL (FOIL TYPE)

UL LISTED TRANSITION DUCT

(IF NEEDED.)

DUCT TAPE

UL RATED

120/240V,30A

WITH 3 OR 4 PRONGS.

IDENTIFY THE PLUG

TYPE AS PER THE

HOUSE RECEPTACLE

BEFORE PURCHASING

LINE CORD.

TOOLS YOU

WILL NEED

SLIP JOINT PLIERS

FLAT BLADE SCREWDRIVER

PHILLIPS SCREWDRIVER

LEVEL

- RISK OF FIRE

WARNING

•

To reduce the risk of severe injury or death, follow all installation instructions.

•

Clothes dryer installation must be performed by a qualified installer.

•

Install the clothes dryer according to these instructions and in accordance

with local codes.

•

This dryer must be exhausted to the outdoors.

•

Use only 4” rigid metal ducting for exhausting the clothes dryer to the

outdoors.

•

Do not install or store this appliance in any location where it could be

exposed to water and or weather.

•

Save these instructions. (Installers: Be sure to leave these instructions with

the customer).

•

DO NOT install a clothes dryer with flexible plastic ducting materials.

If flexible metal (semi-rigid or foil-type) duct is installed, it must be UL listed

and installed in accordance with the instructions found in "Connecting The

Dryer To House Vent" on page 5 of this manual. Flexible venting materials

are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct dryer airflow and increase the risk of fire.

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - Electric Dryer

Questions or Installation? Call: 1-800-GECARES (US)or Visit our Web site at: www.GEAppliances.com (US) InstallationInstructionsElectric Dryer09Ste

Page 2

Installation Instructions1014. Place the door on its edge. Assemble the 2 machinescrews (#8), washers, and nuts. Tighten using awrench and screwdriver

Page 3

Installation Instructions1122. Switch the strike bracket and its cover to the opposite side by removing the screws; then reinstall both on the opposit

Page 4

ROUGH-IN DIMENSIONS1230 5/8"27"40 1/4"53 5/8"39 1/8"13 3/8"11 3/4"17"27"1 5/8"4 1/2"31 1/8"

Page 5 - WALL IS 5.5 IN

L1NL2RELOCATE GREENGROUND SCREWHERESTRAINRELIEFBRACKETGREEN ORYELLOW WIRE3/4", ULRECOGNIZEDSTRAIN RELIEFSCREWS(3)HOTWIREHOTWIRECOVER NEUTRAL(Whit

Page 6

3 #10 AWG MINIMUM COPPERCONDUCTORS OR 120/240V 30A POWERSUPPLY CORD KIT MARKED FOR USEWITH DRYERS & PROVIDED WITH CLOSEDLOOP OR SPADE TERMINALS WI

Page 7

Installation Instructions4EXHAUST CONNECTION4NOTE: ELBOWS WILL PREVENT DUCTKINKING AND COLLAPSING.5LEVELING AND STABILIZING YOURDRYERELBOW HIGHLYRECO

Page 8

Installation Instructions, ExhaustingCONNECTING THE DRYER TO HOUSE VENT56ALCOVE OR CLOSET INSTALLATION• If your dryer is approved for installation in

Page 9

DUCTTAPECAUTION:Internal duct joints must besecured with tape, otherwisethey may separate and causea safety hazard.Installation InstructionsDetach and

Page 10 - Installation Instructions

10REVERSING THE DOOR SWINGIMPORTANT NOTES• Read the instructions all the way through before starting.• Handle parts carefully to avoid scratching pain

Page 11 - Tighten All

Installation Instructions81. Unplug the dryer from its electrical outlet.2. Open the door to approximately 90 degrees. Remove the 4screws starting fr

Page 12 - ROUGH-IN DIMENSIONS

Installation Instructions9IMPORTANT: Note the location of the hinge (left or right) beforeremoving.8. With the door frame part of the door laid down