GE 23503HD Manuel d'instructions télécharger pdf

10"X10"

CAUTION: EXERCISE CARE WHEN UNPACKING AND ASSEMBLING

5 Ft & 6.5 Ft & 7 Ft Winter Berry Branch Tree Assembly Instructions

WARNING: Risk of fire and electric shock. Disconnect light set from power before starting.

1) Keep wires clear of being pinched or cut during assembly or installation.

3) Before starting make sure stakes are clear of underground: sprinkler, telephone and

power lines.

4) Please read all instructions and warnings included with this product before using.

2) Do not press or grasp bulbs during assembly or installation.

NOTE: No tools required

Parts List:

(

1) Top section for all types (1) Middle section for most

(1) Bottom section or Extender for all types (1) Metal stand with legs or flat base

(1) Spare parts bag with metal stakes

Approximate assembly time is 20 minutes

Hammer/Mallet may be required for stakes

Top section for all types

Middle section for most

Bottom section

Extender for all types

Metal stand with legs

or flat base

Spare parts bag with metal stakes

1.Carefully unpack, removing any bubble pack and inspect the contents of your tree.

The spare parts bag is taped to end flap. Retain the shipping carton to repack your tree.

NOTE: If applies, set aside any loose bulbs to reattach later.

2.Remove the tree stand from the storage bag and open. You may need to loosen the

thumbscrew to open base with legs.

Hint: your assembled tree may be heavy and difficult to move so place the stand in the

desired location before assembling. Secure in place using the (4) metal stakes.

NOTE: Stands with legs come with (1) thumbscrew either already threaded into the stand

or packaged separately in a bag. Make certain to locate the thumbscrew before discarding

the bag. If your stand comes with a thumbscrew, it is to be threaded into the stand. Insert

or back-out accordingly.

3.Look for the bottom section or the extender, identified by a red-colored plastic protective

cap at the bottom of the pole. Remove the cap and place into the tree stand. If your stand

has a thumbscrew, fully tighten the thumbscrew.

4.Locate and untwist the red metal tie wrap holding the branches in place. Save this tie

wrap to use when storing your tree.

Hint: If your branches do not fall into place, DO NOT force down. Starting at the bottom

gently lift up on the branches to release them from their locked position. During shipping,

branch tips may become intertwined or entangled. Carefully undo. Now, all rows of

branches should be in the open position. Locate the long lead wire and place it to the side

for later use.

NOTE: If the top and bottom poles are electrically connected or if your tree has only two

sections, skip to step 7.

5.Remove the green protective cap from the middle section.

Find the locating key inside opening. Find groove at top of

the bottom section. Insert the middle section over opening in

bottom section. Rotate slightly until it slides down and is

fully seated. Keep all wires from entering the opening and

damaging the wires.

NOTE: This stabilizes your tree keeping both sections from

turning and properly aligning the branch panels.

6.Untwist the red metal tie wrap holding the branches in

place. Refer to Hint in 4. Save for storing the tree.

7.Insert the treetop into the opening of the lower section and shape, being careful to keep

the cord from entering the opening and damaging the wires. Straighten out the top tips if

necessary.

8.Depending on the Model of your tree electrically connect the lighted sections following

either a) or b) below:

a) End Plugs - Fully insert the plug from the top pole into the end connector near the top of

the lower pole. Continue down to connect the bottom if your tree has (3) lighted section.

b) Connectors – First find the 2 yellow CONNECTOR cord tags located between each section.

First align the 2 pins and flat on the connector and then fully inserting into the other connector.

Fully screw on the cap to secure together. Repeat if your tree has (3) lighted sections.

NOTE: Reattach any loose bulb by fully inserting into an open lamp socket Your winter

Christmas tree is now assembled!

9.To illuminate find and unhank the long lead wire from the bottom lighted section.

Fully insert the plug directly into a working GFCI outlet or an outdoor rated extension cord.

10.Some Models have a dual color, 4-function control box. The functions are: Steady White,

Steady Multi, White & Multi Color Change and Off.

11.Please check your tree for any loose, unlit or damaged bulbs. They must be replaced

promptly in order to maintain the performance and life expectancy of your pre-lit tree.

Trouble Shooting Tips

If one section of your tree does not illuminate,

check that section for loose or missing bulbs or

that all electrical connections on tree are made.

Also, check the fused plug for a missing or

burned out fuse and make certain the wall

switch is turned on.

Tree Storage

When your tree is not in use, be sure to store it

neatly in a cool, dry location protected from

sunlight.

Indoor/Outdoor

2015 Nicolas Holiday Inc.,

9 F., No. 37, Guangfu North Rd.

Taipei, Taiwan 10560

THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.

Printed in China

5BWB15

Your winter Christmas tree

is now complete!

Distributed by Nicolas Holiday Inc.,

1 2

Résumé du contenu

Page 1 - Tree Storage

10"X10"CAUTION: EXERCISE CARE WHEN UNPACKING AND ASSEMBLING5 Ft & 6.5 Ft & 7 Ft Winter Berry Branch Tree Assembly Instructions WARN

Page 2 - Almacenaje del árbol

10"X10"NOTA: No se necesitan herramientasLista de piezas:(1) sección superior para todos los tipos (1) sección in

Commentaires sur ces manuels

Pas de commentaire

GE 23503HD Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Non GE 23503HD. GE 23503HD Instructions / Assembly Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non GE 23503HD