Ge JV247 Manuel d'utilisateur télécharger pdf (Page 6)

BEFORE YOU BEGIN

Installation Range Hood

Instructions

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions

for local inspector’s use.

•

IMPORTANT – Observe all governing

codes and ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

•

Note to Consumer – Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires

basic mechanical and electrical skills.

• Completion time – 30 minutes–3 hours

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

NOTE: Read the ductwork sections only if you do not

have existing ductwork. If you have existing ductwork,

skip to the “Damage” section and proceed.

WARNING – TO REDUCE THE RISK OF FIRE AND

TO PROPERLY EXHAUST AIR, BE SURE TO DUCT AIR OUTSIDE—

DO NOT VENT EXHAUST AIR INTO SPACES WITHIN WALLS OR

CEILINGS OR INTO ATTICS, CRAWL SPACES OR GARAGES.

The venting system must exhaust to the outside.

This hood can be vented vertically through upper cabinets

or horizontally through an outside wall. Ductwork is not

included.

Exhaust connection:

The hood exhaust has been designed to mate with

standard 3

⁄4″ x 10″ rectangular ducting or 7″ diameter

round ducting.

If a 6″ round duct is required, a rectangular-to-round

transition adaptor must be used*. Do not use less than

a 6″ diameter duct.

Maximum duct length:

For satisfactory air movement, the total duct length

of a 3

⁄4″ x 10″ rectangular, 6″ or 7″ diameter round

duct should not exceed 65 equivalent feet. See the

WORKSHEET–CALCULATE TOTAL EQUIVALENT

DUCTWORK LENGTH section.

NOTE: It is important that ducting be installed using

the most direct route and with as few elbows as possible.

This ensures clear venting of exhaust and helps prevent

blockages. Also, make sure dampers swing freely and

nothing is blocking the ducts.

Elbows, transitions, wall and roofcaps, etc.,

present additional resistance to airflow and are equivalent

to a section of straight duct longer than their actual

physical size. When calculating the total duct length, add

the equivalent lengths of all transitions and adaptors plus

the length of all straight duct sections. The charts on the

following pages show you how to calculate total equivalent

ductwork length using the approximate feet of equivalent

length of some typical ducts.

* IMPORTANT: If a rectangular-to-round

transition adaptor is used, the bottom

corners of the damper will have to be

cut to fit, using the tin snips, in order

to allow free movement of the damper.

Equivalent lengths of duct pieces

are based on actual tests and reflect

requirements for good venting

performance with any hood.

DUCTWORK REQUIREMENTS

WARNING – Before beginning the

installation, switch power off at service panel and

lock the service disconnecting means to prevent power

from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten

a prominent warning device, such as a tag, to the

service panel.

FOR YOUR SAFETY:

Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com

An optional Power Cord Connection Kit, model JXHC1,

is available at extra cost from your GE supplier for

installation using a standard 3-prong, grounded wall

outlet. Follow the Installation Instructions packed with

the kit to connect the power cord to the range hood.

OPTIONAL POWER CORD KIT JXHC1

1 2 3 4 5 6 7 8 9 10 11 ... 15 16

Commentaires sur ces manuels

Pas de commentaire

Ge JV247 Manuel d'utilisateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Ventilateurs Ge JV247