Ge GEFanuc Automation Programmable Control Products T Manuel d'utilisateur Page 227
- Page / 268
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
C
C-7
GFK-1004B
Appendix C Soft Switch Parameters
Correct Results of Soft Switch Configuration
If the values displayed from the CHSOSW command are not correct, reenter the
command with the desired parameters. Enter the command SOSW to see the
current Soft Switch values.
If the Soft Switch LED pattern is displayed but no “sign-on message” or prompt
appears on the terminal, check the construction and connections of the serial cable
and verify that the terminal is operating at the 9600 bps data rate. The sign-on
message can be repeated by pressing the LAN Interface Restart button.
- GE Fanuc Automation 1
- Warnings, Cautions, and Notes 2
- Content of this Manual 3
- Related Publications 4
- Contents 10
- Chapter 1 Introduction 15
- The Ethernet Interface 16
- The Ethernet Software 18
- The Configuration Editor 19
- The Downloader 19
- How to Make it Work 20
- Quick Guide to the Manual 21
- Board Indicators 24
- Restart Button 24
- C:\> cd \gsm 29
- C:\GSM> gsm 29
- Problems During Power-Up 31
- Configuring a Station 41
- Downloading a Station 42
- Initiating the Download 43
- Problems During the Download 44
- Running Field Network Test 47
- Configuration 53
- What is the GSM? 54
- Hardware Requirements 56
- Setting-Up DOS System Files 60
- Unusual Procedures 64
- Starting-Up the GSM 65
- GSM Keyboard Functions 67
- GSM Menu Structure 68
- Configure a Station Screen 69
- Structure of the MAC Address 72
- TCP/IP Parameters Screen 74
- Advanced Parameters Menu 76
- Data Link Parameters Screen 77
- System Parameters Screen 79
- Download Station Screen 81
- Downloading Over the Network 82
- Access Station Manager Screen 84
- List All Stations Screen 85
- Setup GSM Menu 87
- Set Download Mode Screen 88
- Exit to DOS 88
- COMMREQ Function Block 91
- COMMREQ Command Block 91
- Channel Commands 91
- Status Data 92
- Domain of a channel 93
- Domain of a TCP connection 93
- The COMMREQ Function Block 94
- The COMMREQ Command Block 95
- Section 3: Channel Commands 97
- Establish Read Channel (2003) 99
- GFK-1004B 102
- Example Command Block 103
- A Channel Command 104
- Abort Channel (2001) 109
- Section 4: Status Data 113
- Types of Status Data 113
- Status Bits 114
- Communications Status Words 117
- Table 4-4. Major Error Codes 118
- Minor Error Codes 119
- FT Output is ON 125
- Chapter 5 The Station Manager 128
- Station Manager Mode 129
- Using the Monitor Commands 133
- Using the Modify Commands 134
- Date and Time 135
- Task Identification 136
- Display Data Representation 136
- Byte String Values 137
- IP Address 137
- Soft Switch Entry Utility 138
- Field Network Test Utility 140
- Command Restrictions 141
- Command Input Processing 142
- CHANNEL Command 143
- BPS Command 144
- CHBPS Command 144
- CHDATE Command 144
- CHLTIME Command 145
- CHSOSW Command 145
- NET Load from network 146
- * Default Value 146
- CHTIME Command 147
- CLEAR Command 148
- CLSOSW Command 148
- DATE Command 149
- EXS Command 149
- HELP Command 149
- LOAD Command 151
- LOG Command 151
- LOGIN Command 152
- LOGOUT Command 153
- LTIME Command 153
- NET Command 153
- NODE Command 154
- OK Command 154
- PING Command 154
- PROG Command 155
- REM Command 155
- REPORT Command 156
- REPP Command 157
- RESTART Command 157
- SHOW Command 158
- Configuration Parameters 159
- <<00080000>> 160
- SOSW Command 161
- STAT Command 161
- STOPP Command 162
- STOPT Command 162
- TALLY Command 163
- Tally Meaning 164
- TEST Command 169
- TIME Command 170
- TRACE Command 170
- Chapter 6 Troubleshooting 172
- Using this Chapter 173
- The Power-Up State 176
- The Soft Switch Entry State 176
- The Field Network Test State 177
- The Loader State 178
- The Operational State 179
- Log Event Cause 181
- Chapter 6 Troubleshooting 182
- Log Event 182
- Appendix A Glossary 208
- Glossary of Terms 209
- What this Appendix Contains 216
- Serial Port Settings 216
- Serial Port Pinouts 216
- Serial Cable 217
- Display Terminal Settings 217
- Ethernet AUI Port Pinouts 218
- AUI (Transceiver Cable) 219
- Transceiver Description 219
- Config Mode 221
- Station Address 222
- Network Load Address 223
- Load Source 223
- LAN Online 223
- Backplane Online 223
- Modify Soft Switch Settings 224
- 3Com Etherlink II 229
- 3Com Etherlink 3 230
- 3Com Etherlink 16 231
- 3Com Etherlink /MC 232
- \CONFIG.SYS 233
- \AUTOEXEC.BAT 233
- \GEFNDIS\PROTOCOL.INI 233
- Intel 82593 234
- Xircom Pocket Adapter (PE2) 235
- Xircom Pocket Adapter (PE3) 236
- IBM PCMCIA 238
- Error Code Description 240
- Table E-2. NDIS Error Codes 242
- Appendix F Network Test Form 243
- Network Test Data Sheet 244
- Addresses 245
- Gateways 246
- MAC Addresses 248
Produits connexes et manuels pour Matériel Ge GEFanuc Automation Programmable Control Products T
Matériel Ge ZBD6905 Manuel d'utilisateur
(16 pages)
(16 pages)
Matériel Ge ZET1 Manuel d'utilisateur
(44 pages)
(44 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels