Ge GEFanuc Automation Programmable Control Products T Manuel d'utilisateur Page 28
- Page / 268
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2
2-7
GFK-1004B
Chapter 2 Installing the Ethernet Interface
Procedure 2: Verifying Proper Power-Up of the Ethernet Interface
Before powering–up the Ethernet Interface, you may wish to connect the GEnet System
Manager (GSM) locally to the Ethernet Interface, and select the “Station Manager” func-
tion from the GSM Main menu. This allows you to observe the progress of the power–
up diagnostics via the Station Manager software on the Ethernet Interface. The GSM is
also used to perform other operations in subsequent Installation Procedures.
Refer to Chapter 3, “The GEnet System Manager”, for instructions on installing the GSM
software on a user-supplied PC-compatible computer.
Note
Alternately, you can use a dumb terminal, or another terminal
emulation product on a PC. However, you will probably find it most
convenient to use the GSM since you will be using the GSM for other
configuration purposes in subsequent steps.
If you do not use the GSM, configure the terminal for 9600 bps, 8 bits, no
parity, and 1 stop bit. See Appendix B, for instructions on making the
serial cable.
Using the GSM “Access Station Manager” Function
The Station Manager software on the Ethernet Interface is accessed by connecting the
Ethernet Interface to a Workmaster or other computer running the GSM software and
selecting the “Station Manager” function from the GSM main menu.
1. There are two ways the GSM can be physically connected to an Ethernet Interface:
Local Connection and Network Connection.
Note
To observe the progress of Power–Up Diagnostics described in this
procedure and to invoke the Field Network Test Utility described in
Installation Procedure 5, the GSM must be connected locally and put in
the Local Station Manager Mode.
A. GSM Using Local Connection. Connect the COM1 RS–232 serial port on the
device running the GSM to the 9–pin connector on the Ethernet Interface. Refer
to Appendix B, for instructions on how to make the RS–232 cable.
B. GSM Using Network Connection. Connect the Ethernet card on the device
running the GSM to the Ethernet Network.
C. For now, use the Local connection.
2. Power–up the computer (on which you have previously installed the GSM software)
into DOS. Refer to Chapter 3 for the GSM installation procedure.
- GE Fanuc Automation 1
- Warnings, Cautions, and Notes 2
- Content of this Manual 3
- Related Publications 4
- Contents 10
- Chapter 1 Introduction 15
- The Ethernet Interface 16
- The Ethernet Software 18
- The Configuration Editor 19
- The Downloader 19
- How to Make it Work 20
- Quick Guide to the Manual 21
- Board Indicators 24
- Restart Button 24
- C:\> cd \gsm 29
- C:\GSM> gsm 29
- Problems During Power-Up 31
- Configuring a Station 41
- Downloading a Station 42
- Initiating the Download 43
- Problems During the Download 44
- Running Field Network Test 47
- Configuration 53
- What is the GSM? 54
- Hardware Requirements 56
- Setting-Up DOS System Files 60
- Unusual Procedures 64
- Starting-Up the GSM 65
- GSM Keyboard Functions 67
- GSM Menu Structure 68
- Configure a Station Screen 69
- Structure of the MAC Address 72
- TCP/IP Parameters Screen 74
- Advanced Parameters Menu 76
- Data Link Parameters Screen 77
- System Parameters Screen 79
- Download Station Screen 81
- Downloading Over the Network 82
- Access Station Manager Screen 84
- List All Stations Screen 85
- Setup GSM Menu 87
- Set Download Mode Screen 88
- Exit to DOS 88
- COMMREQ Function Block 91
- COMMREQ Command Block 91
- Channel Commands 91
- Status Data 92
- Domain of a channel 93
- Domain of a TCP connection 93
- The COMMREQ Function Block 94
- The COMMREQ Command Block 95
- Section 3: Channel Commands 97
- Establish Read Channel (2003) 99
- GFK-1004B 102
- Example Command Block 103
- A Channel Command 104
- Abort Channel (2001) 109
- Section 4: Status Data 113
- Types of Status Data 113
- Status Bits 114
- Communications Status Words 117
- Table 4-4. Major Error Codes 118
- Minor Error Codes 119
- FT Output is ON 125
- Chapter 5 The Station Manager 128
- Station Manager Mode 129
- Using the Monitor Commands 133
- Using the Modify Commands 134
- Date and Time 135
- Task Identification 136
- Display Data Representation 136
- Byte String Values 137
- IP Address 137
- Soft Switch Entry Utility 138
- Field Network Test Utility 140
- Command Restrictions 141
- Command Input Processing 142
- CHANNEL Command 143
- BPS Command 144
- CHBPS Command 144
- CHDATE Command 144
- CHLTIME Command 145
- CHSOSW Command 145
- NET Load from network 146
- * Default Value 146
- CHTIME Command 147
- CLEAR Command 148
- CLSOSW Command 148
- DATE Command 149
- EXS Command 149
- HELP Command 149
- LOAD Command 151
- LOG Command 151
- LOGIN Command 152
- LOGOUT Command 153
- LTIME Command 153
- NET Command 153
- NODE Command 154
- OK Command 154
- PING Command 154
- PROG Command 155
- REM Command 155
- REPORT Command 156
- REPP Command 157
- RESTART Command 157
- SHOW Command 158
- Configuration Parameters 159
- <<00080000>> 160
- SOSW Command 161
- STAT Command 161
- STOPP Command 162
- STOPT Command 162
- TALLY Command 163
- Tally Meaning 164
- TEST Command 169
- TIME Command 170
- TRACE Command 170
- Chapter 6 Troubleshooting 172
- Using this Chapter 173
- The Power-Up State 176
- The Soft Switch Entry State 176
- The Field Network Test State 177
- The Loader State 178
- The Operational State 179
- Log Event Cause 181
- Chapter 6 Troubleshooting 182
- Log Event 182
- Appendix A Glossary 208
- Glossary of Terms 209
- What this Appendix Contains 216
- Serial Port Settings 216
- Serial Port Pinouts 216
- Serial Cable 217
- Display Terminal Settings 217
- Ethernet AUI Port Pinouts 218
- AUI (Transceiver Cable) 219
- Transceiver Description 219
- Config Mode 221
- Station Address 222
- Network Load Address 223
- Load Source 223
- LAN Online 223
- Backplane Online 223
- Modify Soft Switch Settings 224
- 3Com Etherlink II 229
- 3Com Etherlink 3 230
- 3Com Etherlink 16 231
- 3Com Etherlink /MC 232
- \CONFIG.SYS 233
- \AUTOEXEC.BAT 233
- \GEFNDIS\PROTOCOL.INI 233
- Intel 82593 234
- Xircom Pocket Adapter (PE2) 235
- Xircom Pocket Adapter (PE3) 236
- IBM PCMCIA 238
- Error Code Description 240
- Table E-2. NDIS Error Codes 242
- Appendix F Network Test Form 243
- Network Test Data Sheet 244
- Addresses 245
- Gateways 246
- MAC Addresses 248
Produits connexes et manuels pour Matériel Ge GEFanuc Automation Programmable Control Products T
Matériel Ge ZBD6905 Manuel d'utilisateur
(16 pages)
(16 pages)
Matériel Ge ZET1 Manuel d'utilisateur
(44 pages)
(44 pages)
Sharp XG-NV5XU manuály
Uživatelské manuály a uživatelské příručky pro Datové projektory Sharp XG-NV5XU.
Poskytujeme 2 manuály pdf Sharp XG-NV5XU ke stažení zdarma podle typů dokumentů: Uživatelský manuál, Specifikace
Commentaires sur ces manuels