GE EPM 5300 Manuel d'utilisateur Page 64
- Page / 100
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CHAPTER 10: PROGRAMMING GROUP 1
60
EPM 5000 series Advanced Power Meters GE Multilin
SECONDARY PT VALUES PT RATIO FULL SCALE
75 V (Suffix 75) L-N MAX 120:1 9.00 KV
120/208 V 1:1 (Direct) 120.0
120/208 V 4:1 0480 V
120/208 V 120:1 014.4 KV
277/480 V (Suffix G) 1:1 (Direct) 0300 V
120/208V 600:1 072.0 KV
120/208 1150:1 138.0 KV
Table 10-2: TYPICAL Full Scale Settings for Volts
If PT is connected line to line, the full scale can be 14.40 KV. Full scale is 300 V L-N, not 277, because
the factory calibration is 300 V. Be sure the table is based on a meter regulation of 2000 A/D counts.
Thus, for best accuracy, all settings should be placed within that range.
VOLTAGE FULL SCALE:
To change the Full Scale Settings:
NOTE: Press MAX/MIN/LIMITS at any time to cancel before storing the last digit or switch.
MAX/MIN
LIMITS
KVAR
PF
KW
KV
A
FREQ
KWH
KVAH
AC VOLTS
AC AMPS
POWER
NCB
A
MAX
MIN
A
N
B
N
C
N
A
B
B
C
C
A
LM2
LM1
NEXT
PHASE
V
OLTS
AMPS
POWER
MAX/MIN
LIMITS
KVAR
PF
KW
KVA
FREQ
KWH
KVAH
AC VOLTS
AC AMPS
POWER
NCBA
MAX
MIN
A
N
B
N
C
N
A
B
B
C
C
A
LM2
LM1
NEXT
PHASE
VOLTS
AMPS
POWER
Step 1:
a. Enter Group Level of Programming Mode
(see Chp. 8).
b. Press MAX/MIN/LIMITS until 1. appears in upper
display.
Step 2:
a. Press AMPS to activate GROUP 1.
! 10. appears in upper display.
! Middle display indicates Scale Factor Setting.
! Lower display indicates Full Scale for voltage.
- Instruction Manual 1
- TABLE OF CONTENTS 3
- CHAPTER 1 5
- AC POWER MEASUREMENT 5
- 1.2: Three-Phase System 6
- 1) Delta 7
- 1.4: Waveform and Harmonics 8
- % THD GRAPH 8
- CHAPTER 2 9
- MECHANICAL INSTALLATION 9
- BACK VIEW 10
- CHAPTER 3 11
- ELECTRICAL INSTALLATION 11
- LIST OF CONNECTION DIAGRAMS 13
- EPM 5300P RELAY OVERVIEW 18
- CONNECTION FOR DB-9 FEMALE 21
- 5300P Instruments (rear view) 22
- Communications Port 23
- Model #SF485DB 23
- UNICOM 2500 24
- (Bottom View Shown) 24
- Model#SF485DB 25
- COMPUTER 27
- CHAPTER 5 31
- OVERVIEW 31
- AC VOLTS 32
- 5.6: Resetting Values 34
- UNPROTECTED RESET 35
- PROTECTED RESET 35
- 5.7: Resetting Hour Readings 36
- 5.10: Access Modes 38
- 5.11 Print Operating Data 38
- 5.12: Print Programming Data 39
- CHAPTER 6 41
- PROGRAMMING OVERVIEW 41
- SED FOR PROGRAMMING 42
- ASSWORD ENTRY 42
- CHAPTER 7 43
- EPM 5200P 43
- CHAPTER 8 45
- ENTERING PROGRAMMING MODE 45
- CHAPTER 9 47
- FUNCTION 50
- 9.5 Modbus Plus Capability 52
- PRINTING OPTION 52
- 9.7: Relay Mode 54
- DEFINITIONS: 54
- PROGRAMMING STEPS: 55
- CHAPTER 10 63
- SETTINGS 63
- VOLTAGE FULL SCALE: 64
- NTERING THE SCALE FACTOR: 65
- ECIMAL POINT SELECTION: 65
- YPE FULL SCALE 66
- CHAPTER 11 71
- CHAPTER 12 75
- AC AM PS 76
- RELAY 2 77
- SPECIAL CASES 78
- UNCTION 79
- Over/Under %THD Conditions 80
- 13.2: Trip Relay 83
- CHAPTER 14 87
- EXITING PROGRAMMING MODE 87
- CHAPTER 15 89
- PROGRAMMING QUICK REFERENCE 89
- 15.6: Group 2: Calibration 91
- 15.10: Group 6: THD Limits 92
- KEY DESIGNATIONS 93
- CHAPTER 16 95
- ETHERNET OPTION 95
- 16.2: Ethernet Option Setup 96
- 16.3: Default IP Address 97
- 16.4: AutoIP 97
- 16.5: Setting the IP Address 97
- 16.6: Network Configuration 98
- Multilin 100
Produits connexes et manuels pour Mesure, test et contrôle GE EPM 5300
(68 pages)LG V-C3G51NTU manuali
Manuali dei proprietari e guide per l'utente per no LG V-C3G51NTU.
We fornisce 1 manuali pdf LG V-C3G51NTU per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commentaires sur ces manuels