Ge 2-9079 Manuel d'utilisateur

We bring good things to life.2-9079Caller ID

8TWO-LINE SYSTEM INSTALLATIONYou must use two caller ID units if youwant to use caller ID for both lines. Youmust also purchase a triplex adapter.1. P

9OPERATIONCHOOSING A LANGUAGEYour caller ID unit is programmed at the factory to display messages in English, but youcan change the language setting t

10RECEIVING AND STORING CALLSThe display automatically lights when there is a new calland whenever you press any of the buttons on the unit.This unit

11DELETEVIPDISPLAYREVIEWDELETE AND REVIEW BUTTONSDELETE BUTTON• To delete THE record shown in the display, pressthe DELETE button.• To delete ALL reco

12VERY IMPORTANT PERSON BUTTONUse VIP memory for numbers you want to save. Youcan store up to 20 names and numbers. To save anumber into VIP memory

13DELETE VIP NUMBERS1. Press VIP to enter VIP memory.2. Press the REVIEW buttons until you reachthe desired VIP number you to delete.3. Press DELE

14MESSAGE INDICATORSThe following messages tell you what your unit is doing.BATTERY iconBattery power level is low.BLOCKED NAMECaller ID information i

15no CALLThe caller ID memory is empty.NO DATA SENTThe incoming call does not have caller ID service or their servicearea is not linked to yours.RECOR

16TROUBLESHOOTING TIPSNO DIAL TONE ON THE PHONE ATTACHED TO THE CALLER ID UNIT• Check all cabling to make sure that all connections are secure.• Check

17GENERAL PRODUCT CARETo keep your Caller ID working and looking good, follow these guidelines:• Avoid putting it near heating appliances and devices

INTRODUCTIONYour GE Caller ID unit stores and displays specific information, provided by your localtelephone company, to subscribers of Caller ID or s

18SERVICEFCC requires this product to be serviced only by the manufacturer or its authorizedservice agents. In accordance with FCC requirements, chang

19FCC REGISTRATION INFORMATIONYour GE telephone equipment is registered with the Federal Communications Commission and is in compliance withparts 15 a

20INTERFERENCE INFORMATIONThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thisdevice may

21LIMITED WARRANTYWhat your warranty covers:• Any defect in materials or workmanship.For how long after your purchase:• One year.(The warranty period

Model 2-9079347A8359-0001 (Rev. 0 E/S)96-30Printed in Hong KongP.O. Box 1976, Indianapolis, IN 46206© 1996 Thomson Consumer Electronics, Inc.Trademark

1BEFORE YOU BEGINPARTS CHECKLISTMake sure your package includes the following items:MODULAR JACK REQUIREMENTSYou need an RJ11 type modular jack, which

2POWERING THE CALLER ID UNITThe unit can operate on batteries only, but you mustuse the AC power supply in order for the new callindicator light and t

3BATTERY INDICATORIf the battery icon appears in the display, you need toreplace the batteries.USING THE AC ADAPTERYou must use the AC power supply in

4INSTALLATIONYou can set the unit on a tabletop or mount it on the wall.IMPORTANT INSTALLATION INFORMATION• Never install telephone wiring during a li

5TABLETOP INSTALLATION1. Connect the telephone line cord to the jack on theback of the unit marked TO LINE, and to themodular wall jack.2. Connect you

6WALL MOUNT INSTALLATIONUse the mounting accessories included with this unit.1. Hold the mounting bracket against the wall andmark the mounting screw

7ANSWERING MACHINE INSTALLATIONThe answering machine must be set to answercalls after at least 2 rings to properly receive callerID information. To us