Ge CGS980 Manuel d'utilisateur télécharger pdf (Page 33)

Consumer SupportInstallation Instructions Troubleshooting TipsOperating InstructionsSafety Instructions

ge.com

Burner Caps and Heads

Before removing the burner caps and heads, remember

their size and location. Replace them in the same location

after cleaning.

NOTE: Do not use steel wool or scouring powders to clean

the burner parts.

Burner caps

Lift off when cool. Wash burner caps in hot,

soapy water and rinse with clean water. You may

scour with a plastic scouring pad to remove

burned-on food particles.

Burner Heads and Oval (Center) Burner

Head/Cap Assembly

The burner heads and the oval burner head/cap assembly

are removable. Simply lift them off the range for cleaning.

For proper ignition, make sure the small hole

in the section that fits over the electrode is kept

open. A sewing needle or wire twist-tie works

well to unclog it.

The slits in the burner heads must be kept clean at all

times for an even, unhampered flame.

Clogged or dirty burner ports or electrodes will

not allow the burner to operate properly.

Any spill on or around an electrode must

be carefully cleaned. Take care to not hit an

electrode with anything hard or it could be

damaged.

Clean the burner heads routinely, especially after

bad spillovers, which could clog the openings.

Lift off when cool.

To remove burned-on food, soak the burner

heads in a solution of mild liquid detergent and

hot water for 20–30 minutes. For more stubborn

stains, use a toothbrush.

After cleaning

Before putting the burner caps, heads and oval

head/cap assembly back, shake out excess water

and then dry them thoroughly by setting in a

warm oven for 30 minutes.

Replacement

Burner Heads

Replace burner heads over the electrodes on

the cooktop, in the correct locations according

to their size. There is one small, one medium,

one extra large and one dual flame extra large

burner head.

Make sure the slot (on front left, back right and

back left heads) and the hole (front right head)

in the burner head is positioned over the

electrode.

Oval (Center) Burner Head/Cap Assembly

Replace the oval (center) head/cap assembly

over the electrode on the cooktop.

Caps

Replace the matching size caps onto the burner

bases or heads.

Make sure that the heads and caps are replaced

in the correct locations.

The oval burner head/cap assembly is

removable. Simply lift it off the range

for cleaning. Use a sewing needle or

twist-tie to unclog the small hole in the

burner heads.

Burner cap is

properly seated.

Burner cap is NOT

properly seated.

Electrode

Slot

Front of range

Oval head and cap

assembly

Medium head

Front of range

Extra large

head

Small head

Dual flame

extra large head

Medium cap

Front of range

Extra large cap

Small cap

Dual flame extra

large cap

Make sure the slot in the

burner head is positioned

over the electrode.

Hole in

burner

head

Slot

Electrode

Burner head

Electrode

Burner head

Front right head

Hole

Electrode

Burner cap

Burner head

Burner base

Front right burner

Make sure the hole in the burner

head is positioned over the electrode

and that the burner head is fully

inserted inside the burner base.

A small gap between the base and

head is normal.

Electrode

Burner cap

Stability

chamber

Burner base

Front left burner, back right burner

and back left burner

Make sure the slot in the burner head

is positioned over the electrode.

Burner head

Use a sewing

needle or

twist-tie to

unclog the

small hole in

the burner

head.

Front left, back right

and back left heads

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 59 60

Commentaires sur ces manuels

Pas de commentaire

Ge CGS980 Manuel d'utilisateur Page 33

Commentaires sur ces manuels

Produits connexes et manuels pour Radio Ge CGS980