GE ZV830 Manuel d'utilisateur télécharger pdf (Page 9)

INSTALL FRAMING

FOR HOOD SUPPORT

IMPORTANT— Framing must be capable

of supporting 100 lbs.

If drywall is present, mark the screw hole locations for

the top mounting brackets. Remove the template.

• Cut away enough drywall to expose 2 vertical studs

at the bracket location indicated on the template.

• Install a horizontal support at least 1

″ x 6″

between two wall studs at the mounting screw

location. The horizontal support must be flush with

the room side of the studs. Use cleats behind both

sides of the support to secure to wall studs.

IMPORTANT: Reinstall drywall for an even mounting

surface.

Centerline of

Installation

Space

8" Min. Opening for Ductwork

View From Rear

Cleats

1" x 6" Min.

Mounting

Support

Installation Instructions

Centerline of

installation

space

View from rear

cleats

1” x 6” min.

mounting

support

DUCTWORK, WIRING LOCATIONS

Determine the exact location of the vent hood.

• Locate the template packed with the literature.

– Measure 36″ from the floor to the top of the cooking

surface. Add hood installation height determined on

page 7. Mark that location.

– Use a level to draw a straight pencil line on the wall.

– Tape the template in position along the penciled

line. CHECK TO BE SURE THE TEMPLATE IS LEVEL.

Ceiling ducting:

If ductwork will vent straight up to the ceiling:

• Use a level to draw a line straight up, from

the centerline on the template to the ceiling.

• Measure 5-1/2

″ from the back wall to the centerline

of an 8-1/2

″ hole on the ceiling.

NOTE: If drywall is not present, add drywall thickness

to the 5-1/2

″ dimension.

Wall Ducting:

If ductwork will vent to the rear:

• Use a level to draw a line straight up from

the centerline on the template.

• Measure at least 27-3/4

″ above the pencil line

that indicates the bottom installation height, to the

centerline of an 8-1/2

″ dia. duct hole. (Hole may

be elongated for duct elbow.)

HOUSE WIRING LOCATION:

• The junction box is located on the top left side

of the hood.

• Wiring should enter the back wall at least 18

″ above

the bottom of the hood, and within 5-1/2

″ of the left

side of the centerline.

INSTALLATION—VENTED TO THE OUTSIDE

8-1/2” min. opening for ductwork

Installation Height

Align Bottom Edge With

Pencil Line Indicating

Bottom of Hood

REAR WALL

MOUNTING TEMPLATE

49-80514 10/07 JR

Printed in Mexico

15-7/16″

10-1/16″

1-1/4″

9-7/16″

TOP

MOUNTING

HOLE

DRILL 1/8″

PILOT HOLE

TOP

MOUNTING

HOLE

DRILL 1/8″

PILOT HOLE

BOTTOM

MOUNTING

HOLE

BOTTOM

MOUNTING

HOLE

NOTE:To p

mounting

screws MUST

engage wood

support.

NOTE: Top

mounting

screws MUST

engage wood

support.

Installation Height

Align Bottom Edge With

Pencil Line Indicating

Bottom of Hood

Ceiling

House Wiring

Location

5-1/2”

18”

Min.

Wall vent

27-3/4” min.

above

installation

height

5-1/2” centerline to wall

FOR CEILING VENT DUCTING

8-1/2” dia. hole

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 59 60

Commentaires sur ces manuels

Pas de commentaire

GE ZV830 Manuel d'utilisateur Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Hottes de cuisine GE ZV830