GE JV966DSS Manuel d'utilisation et d'entretien télécharger pdf (Page 9)

Installation Instructions

ADVANCE PLANNING

Ductwork Planning

• This hood may be vented vertically through upper

cabinets, soffit or ceiling. A duct transition piece is

supplied for vertical exhaust. Use locally supplied

elbows to vent horizontally through the rear wall.

See page 13.

• Determine the exact location of the vent hood.

• Plan the route for venting exhaust to the outdoors.

• Use the shortest and straightest duct route possible.

For satisfactory performance, duct run should not

exceed 100 equivalent length for any duct

configurations.

• Refer to “Duct Fittings” chart to compute the maximum

permissible length for duct runs to the outdoors.

• Use metal ductwork only.

• A transition piece for 7 round duct is supplied. Use

7 round duct or you may use 3-1/4 x 12 rectangular.

• Install a wall cap or roof cap with damper at the

exterior opening. Order the wall or roof cap and

any transition needed in advance.

Kit – JXDW1

Order kit JXDW1 if your installation requires horizontal

ducting from the top of the hood through the back wall and:

• You have an 8 ft. ceiling and need to use a JXCH

Series Chimney Cover, or

• You have a 12 cabinet or 12 soffit that the hood is to

be mounted beneath.

This kit provides a duct transition from 7 round to

⁄4 x 10 rectangular for through-the-wall venting.

Wall Framing for Adequate Support

• This vent hood is heavy. Adequate structural support

must be provided. The hood must be secured to

vertical studs in the wall. See page 14.

• We strongly recommend that the vent hood with

duct cover be on site before final framing and wall

finishing. This will also help to accurately locate the

ductwork and electrical service.

DUCT FITTINGS

Follow these guidelines for proper duct sizing in the

ducting charts.

POWER SUPPLY

IMPORTANT – (Please read carefully)

WARNING:

FOR PERSONAL SAFETY, THIS APPLIANCE MUST

BE PROPERLY GROUNDED.

Remove house fuse or open circuit breaker before

beginning installation.

Do not use an extension cord or adapter plug with

this appliance. Follow National electrical codes or

prevailing local codes and ordinances.

Electrical supply

This vent hood must be supplied with 120V, 60Hz, and

connected to an individual, properly grounded branch

circuit, and protected by a 15 or 20 amp circuit breaker

or time delay fuse.

• Wiring must be 2 wire with ground.

• If the electrical supply does not meet the above

requirements, call a licensed electrician before

proceeding.

• Route house wiring as close to the installation

location as possible in the ceiling, soffit or wall.

See page 13 for details.

• Connect the wiring to the house wiring in

accordance with local codes.

Grounding instructions

The grounding conductor must be connected to a

ground metal, permanent wiring system, or an

equipment-grounding terminal or lead on the hood.

WARNING: The improper connection

of the equipment-grounding conductor can result in a

risk of electric shock. Check with a qualified electrician

or service representative if you are in doubt whether

the appliance is properly grounded.

MAXIMUM DUCT LENGTH: 7 dia. duct, should not

exceed 100 equivalent feet.

025

75 100 125 150

600

500

400

300

Air Volume in CFM

7" Round 90 Elbow = 14 ft.

7" Roof Cap = 39 ft.

DUCTING CHART - 30" and 36" Models

Equivalent Length in Feet For 7" Round Duct

200

DECORATIVE DUCT COVERS

A decorative duct cover is available to fit both model

widths. The duct cover conceals the ductwork running

from the top of the hood to the ceiling or soffit. The

duct cover will fit 8 ft. to 10 ft. ceiling heights. See page

12 for details.

″

″″

″

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 47 48

Commentaires sur ces manuels

Pas de commentaire

GE JV966DSS Manuel d'utilisation et d'entretien Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Hottes de cuisine GE JV966DSS