GE WMK35 Brochure télécharger pdf (Page 60)

See page 83 for warranty information.

Dishwasher Specifications

Either single- or double-bowl sink may be used, centered or offset, as shown in the front illustration above. The 20-1/2" max.

dimension from wall to front of sink bowl must be accurate if dishwasher is to fit properly under sink. Water lines to sink

faucet and drain from sink can be run through area “A.” HOT WATER line to dishwasher is installed in area “B.” Garbage

disposer, water lines to faucet, trap, waste air gap and water cut-off valve are installed in 12" wide cabinet shown in area “C.”

Sink opening for garbage disposer must be dimensioned as shown in front view, area “C” above (7-1/2"). This will provide

clearance for disposer and plumbing in cabinet “C” when using double bowl sink. If the sink bowl is more than 20-1/2" max.

specified distance from the wall, or if the base cabinet is less than the 24" min. depth from the wall, a gap between the tub

front flange and the front of the base cabinet may result.

Plumbing/Electrical Rough-In (in inches)

Plumbing: Hot Water Only: Use 3/8" O.D. copper tubing or 1/2"

O.D. plastic tubing min. inlet line. Water valve has 3/8" internal

threads. Hand cut-off valve is recommended.

Electrical: Fuse circuit with 15 amp or 20 amp standard fuse or

circuit breaker. Total amp load is 6.2. Dishwasher operates on

120V, 60 Hz power. Two-wire cable (14 Ga. Min.) with ground

must be installed.

Note: All rough-in, both plumbing and electrical, must be

completed before the dishwasher is installed. All plumbing

and electrical work must be in accordance with local codes.

Specifications: Inlet Water Temperature Recommended: Minimum

120°F at dishwasher. Inlet Water Pressure Required: 15 to 120

lbs./sq. in.

Cabinet Cutout for Sink (in inches)

Cabinet cutouts for offset single and double bowl

sinks. Dishwasher not provided with complete

enclosure. Enclosures for sides, top, bottom,

and back must be provided by installer at time

of installation.

Stainless Steel Sinks Single- and

Double-Bowl Models Dimensions (in inches)

Cutout In

Countertop

1-1/2" Radius

Model Number Corners

L W

GPF95 (Single Bowl, R)* 24-3/8 20-5/8 3 or 4** 10

GPF96 (Single Bowl, L)* 24-3/8 20 -5/8 3 or 4** 10

GPF97 (Double Bowl) 32 -3/8 20 -5/8 3 or 4** 12-1/2

Note: Drain opening size is 3 -1/2".

Above models are fully sound deadened.

*Suffix “L” or “R” means drain outlet is located in upper left or

right corner of sink compartment.

**All have four holes, but one hole has a removable plug.

No. Of

1 -1/2"

Dia.

Faucet

Holes

Ship.

Wt.

Lbs.

A close-fitting elbow or special shallow sink strainer is necessary to provide clearance between sink drain and dishwasher.

Dishwasher furnished with 1/2" I.D. drain hose, 78" long. If using copper tubing, 2" length of 1/2" I.D. rubber hose must be

provided to connect copper tubing to pump outlet. Disposer should have 7/8" I.D. dishwasher drain connector.

Rough-In for Installation with Disposer (in inches) Rear View Plumbing Arrangement (in inches)

3-1/4

12-1/2

Sink

installation

cutout

8" x 20" Adjacent

cabinet rear cutout

Cabinet side

adjacent to D/

FRONT VIEW

Access insert

Door insert

3-11/16

23-9/16

18-7/8

Cabinet cutouts for offset single and double

bowl sinks. Dishwasher not provided with

complete enclosure. Enclosures for sides,

top, bottom and back must be provided by

installer at time of installation.

Inserts must not

exceed 1/4" thickness

within 5/16" of

edge around full

circumference.

Countertop 1-1/2" MIN. thick

FRONT VIEW

7-1/2

6" MAX.

12"

MIN.

Floor

Toe

kick

area

Front of cabinet

Flange

4" MAX.

11-3/4"

MAX. Plumbing

1-1/4"

MIN. I.R.

34-1/4

± 1/4

3/4" MIN.

Wall

Floor

6" MAX.

11" MIN

Drai

20-1/2" MAX.

Sink bowl

1" MAX. to

sink flange

10-1/4" MAX.

Plumbing dept

SIDE VIEW

Dishwasher

Either single- or double-bowl sink may be used, centered or offset, as

shown in the front view illustration. The 20-1/2" MAX. dimension from wal

to front of sink bowl must be accurate if dishwasher is to fit properly

under sink. Water lines to sink faucet and drain from sink can be ru

through area “A.” HOT WATER line to dishwasher is installed in area “B.”

Garbage disposer, water lines to faucet, trap, waste air gap and water

cutoff valve are installed in 12" wide cabinet shown in area “C.” Sink

opening for garbage disposer must be dimensioned as shown in front

view, area “C” (7-1/2"). This will provide clearance for disposer and

plumbing in cabinet “C” when using double bowl sink. If the sink bowl is

more than 20-1/2" MAX. specified distance from the wall, or if the base

cabinet is less than the 24" MIN. depth from the wall, a gap between th

tub front flange and the front of the base cabinet may result.

10-1/4" MAX.

11-3/4

24"

min. cabinet

Spacemaker Dishwasher Dimensions

(Pub. 1-G003 pg. 132B) May 12, 1993

2" From

cabinet

2" From

floor

19" From

wall

Cable 24"

from wall

White (neutral)

Black (line)

Ground

Plumbing and

wiring must enter

within this area

from either side,

rear or bottom

DW PLUMBING/ELECTRICAL

ROUGH-IN (IN INCHES)

FRONT VIEW

Hot

Cold