GE PDT720SGHWW Manuel d'instructions télécharger pdf (Page 14)

Dishwasher Installation

STEP 20: DISHWASHER WET TEST

• Turn on power supply or plug power cord into outlet,

if equipped.

• Select a cycle to run and push the Start button.

• Ensure the door is latched. Dishwasher should start.

• Check to be sure that water enters the dishwasher. If water

does not enter the dishwasher, check to be sure that water

and power are turned on.

• Check for leaks under the dishwasher. If a leak is found, turn

off power at the breaker, and then tighten water connections.

Restore power after leak is corrected.

• Check for leaks around the door. A leak around the door could

be caused by door rubbing or hitting against

DGMDFHQWFDELQHWV5HSRVLWLRQWKHGLVKZDVKHULIQHFHVVDU\

See Step 13.

• Press and hold the Start button for 3 seconds to cancel

the cycle. The unit will begin to drain. Check drain lines. If

leaks are found, turn off power at the breaker and correct

plumbing as necessary. Restore power after corrections are

made. See Steps 7, 8, 9, 10 and 17.

• Open dishwasher door and make sure all of the water has

drained. If not, check that disposer plug has been removed

and/or air gap is not plugged. Also check drain hose to be

sure it is not kinked underneath or behind dishwasher. See

Step 17.

• Press Start button once again and run dishwasher through

another cycle. Check for leaks and correct if required.

• Repeat this step as necessary.

STEP 21:

REPLACE FLOOR PROTECT

(on some models)

• Slide Floor Protect under dishwasher.

• Angle the rear back edge of the Floor Protect upwards to

engage mounting tabs.

• Lift front of drip tray and secure with 2 screws.

• Connect leak sensor connector to leak sensor.

Floor Protect

Leak sensor

Figure AE

STEP 22: POSITION INSULATION, PRE-

TOEKICK, AND SOUND BARRIER

(on some models)

Skip this step if the sound insulation package is not supplied

with the dishwasher.

• Locate the sound insulation package and pre-toekick

packages inside the dishwasher.

• Stand the parts upright as shown.

• Locate the control box.

• Push insulation block portion under the dishwasher until it is

beneath the control box.

• Push the panel portion up to the front of the block.

• Tuck the sides of the front panel behind the toekick

attachment screw holes.

• Open door all the way, if the door doesn’t stay fully open,

DGMXVWWKHLQVXODWLRQSDQHO

• On models so equipped, position pre-toekick over the

insulation. Align the screw holes with the screw holes on the

legs of the dishwasher.

Toekick

Panel

(On some

models.)

Insulation

Block

(On some

models.)

Dishwasher

Door

Pre-

Toekick

(On some

models.)

Sound barrier

(On some

models. Part is

already attached

to door.)

Push the sides of the insulation behind

the toekick attachment screw holes

Figure AF

Control Box

Figure AG

Figure AH

WARNING:

:KHQUHLQVWDOOLQJWKHÀRRUSURWHFWSDQPDNHFHUWDLQWKDWWKH

screws have been fully secured. This will ensure that if the unit is

SURSHUO\JURXQGHGWKDWWKHÀRRUSURWHFWSDQZLOODOVREHJURXQGHG

(on some models)

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 47 48

Commentaires sur ces manuels

Pas de commentaire

GE PDT720SGHWW Manuel d'instructions Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle GE PDT720SGHWW