Ge DLSR483GGWW Manuel d'utilisateur télécharger pdf (Page 2)

For answers to your Monogram,

GE Profile

™

appliance questions, visit our website at

ge.com or call GE Answer Center

service,

800.626.2000.

370119

Specification Revised 5/09

DLSR483GG

Long Vent Super 7.0 Cu. Ft. Capacity Gas Dryer

For complete information, see installation instructions packed with your dryer.

Ducting Materials:

For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If

rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit

WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent

using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY

in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where

a 4” diameter can be maintained throughout the entire length of the transition duct. Please see

installation instruction packed with your dryer for complete instructions when using flexible metal

(foil type) ducting.

Exhaust Length Calculation:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or

bottom of dryer, add one turn.

2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown

in the table.

2. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as

a 90° elbow.

A turn over 45° should be treated as a 90° elbow.

Dryers must be exhausted to the outside.

Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house

floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or mois-

ture could cause damage. Never terminate the exhaust into a common duct or plenum with a

kitchen exhaust, since the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting,

etc. The wall cap must also be located at least 12" above the ground or any other obstruction with

the opening pointed down.

For more information on venting kits and accessories, please call 1-800-GE CARES.

Special Installation Requirements

Alcove or Closet Installation:

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.

• The dryer MUST be exhausted to the outside.

• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:

0" either side

3" front and rear

• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".

• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open

area equally distributed. If this closet contains both a washer and a dryer, doors must contain

a minimum of 120 sq. in. of open area equally distributed.

• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

Bathroom or Bedroom Installation:

• The dryer MUST be exhausted to the outdoors.

• The installation must conform with the local codes, or in the absence of local codes, with the National

Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

Minimum Clearances other than Alcove or Closet Installation:

• Minimum clearances to combustible surfaces

0" both sides

3" rear

Dimensions and Installation Information (in inches)

Best performance

Domestic

dryer models

Maximum length of 4"

dia. rigid metal duct

Number

90°

turns

Exhaust hood type

opening

2-1/2"

opening

DLSR483EG/GG

150 ft.

135 ft.

125 ft.

115 ft.

105 ft.

95 ft.

125 ft.

115 ft.

105 ft.

95 ft.

85 ft.

75 ft.

2-1/ 2

1 2 3

DLSR483GG 1

Commentaires sur ces manuels

Pas de commentaire

Ge DLSR483GGWW Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Séchoirs Ge DLSR483GGWW