GE MN-ValVue-v2-8-IOM Manuel de service Page 653
- Page / 660
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
653
Menu - Status
Setup- In this mode you can set calibration and
configuration parameters. Additionally you can run
response time tests, step response tests, and positioner
signatures. (indicator yellow).
Status Code List
LOW POWER: Indicates that the signal is below 3.8 mA.
RESET_OCCURRED: A reset has occurred either because of a power interruption or
because of an external request for reset.
POSITION_ERROR: The valve failed to go the requested position within the required
time.
BIAS OUT OF RANGE: The integral term of the PID position control has reached its
limits without the valve reaching the proper position.
AUTOTUNE FAILED: The autotune process failed to find reasonable values for PID.
FIND_STOPS_FAILED: The calibration procedure for position failed to find reasonable
values.
CALIBRATE FAILED: The pressure or signal calibration failed because the values were
out of range.
STANDARD DIAGNOSTIC FAILED: The standard actuator signature failed to complete.
EXT DIAGNOSTIC FAILED: The extended actuator signature failed to complete.
CONFIGURATION CHANGED: You have changed one or more of the configuration or
calibration values since the last time this flag was cleared.
ACTUATOR ERROR1: Air pressure has been lost or the calibration of the valve position
endpoint has significantly changed.
SELF_CHECK_FAILURE: On startup, the SVI did not pass a self check.
SOFTWARE_ERROR: An inconsistency has been detected within the SVI.
DATA_OVERRUN: The SVI is not processing acquired data.
POSITION_SENSOR_ERROR: The position sensor has failed or its connection is open.
CURRENT_SENSOR_ERROR: The input signal measurement sensor has failed.
REFERENCE_VOLTAGE_ERROR: The primary reference voltage inside the SVI is
incorrect and all other measurements are likely affected.
INTERNAL_TEMP_ERROR: Internal temperature of the SVI is above or below the rated
temperature.
EEPROM_WRITE_FAILED: A write to the SVI’s internal memory failed.
Menu -
Status
Help- Displays the help file at the
Configure
tab instructions.
- Masoneilan 1
- Products 1
- ValVue* Software v2.8 1
- About this Guide 2
- Copyright 2
- Contents 3
- Introduction 17
- About this Manual 18
- Administration 19
- HART Compliance 20
- Failure to Communicate 20
- Installing ValVue 21
- Figure 2 License Agreement 22
- Installing ValVue 23
- Figure 4 Install ValVue 23
- Figure 5 Finish Installation 23
- Add Users 27
- Editing User Accounts 28
- Deleting a User Account 28
- Privilege Level 29
- Starting ValVue 30
- Registering ValVue 30
- Using Unregistered Software 37
- Offline Mode 37
- Offline Operation 38
- ValVue Setup 41
- Mux Setup 46
- Mux Reset 48
- Troubleshooting ValVue Mux 50
- Configuring Burst Mode 51
- Connecting Devices 53
- Selecting a Device 54
- Advanced Setup with 57
- Configuration Parameters 58
- Calibration Steps 58
- Tri-Loop Configuration 63
- SVI II AP Software Manual 65
- ValVue SVI II AP Work 67
- Working in ValVue 68
- ValVue Help 69
- ValVue Screens 71
- SVI II AP Monitor 73
- Button and Fields 74
- SVI II AP Monitor Screen 75
- Changing the Setpoint 76
- Status on the Monitor Screen 77
- Setting the Air Action 85
- Calibrate Travel 85
- Setup Selections Made 86
- Progress Dialog 87
- Restore SVI Data 91
- Reports 95
- General Information 97
- Operating Data 97
- Configuration Information 97
- Tag Information 100
- Tag Information 101
- Configure Screen 101
- Characterization 102
- Custom Characterization 103
- Bumpless Transfer 107
- Near Closed 107
- Button Lock 107
- Position Limit Stops 108
- Single/Double Acting 108
- Air-to-Open / Air-to-Close 108
- Position Fault Limits 108
- Language 108
- Pressure Units 109
- Configure I/O 109
- Output Switches (DO) 110
- Digital Input (DI) 111
- Input Signal Range (AI) 111
- Position Retransmit (AO) 111
- Burst Settings 112
- Configure Context Menu 113
- Custom Linearization 114
- Trend Screen 117
- Trend Graph Features 118
- Trend Context Menu 120
- Calibrate Screen 121
- Signal Calibration Procedure 122
- High signal Value Calibration 124
- Advanced Parameters 127
- Calibrate Context Menu 129
- Reset to Factory Cal 130
- Live Tuning 131
- Diagnostics Screen 133
- Diagnostic Tests 134
- Speed Level 137
- Select Curve 139
- Data Points 139
- Select curve 139
- Signature 1 139
- Signature 2 139
- Step Test 142
- Ramp Test 144
- Diagnostics Context Menu 147
- Reset Continuous Diagnostics 148
- Status Screen 149
- Clear Current Faults 150
- Clear All Faults 150
- Status Code List 150
- Status Code List 151
- GE Oil & Gas 152
- Table 9 LCD Error Messages 159
- Status Context Menu 161
- Check Screen- Advanced 163
- Troubleshooting 163
- Information Displayed 164
- Check Context Menu 164
- Set I/P Edit Box 165
- I/P Indicator 165
- Changing HART 167
- Versions 167
- References 169
- Technical Release 170
- Revision History 171
- Technical Release Notes.doc 172
- Supported HART Modems 175
- (End of Document) 182
- SVi1000 Software Manual 185
- ValVue Overview 188
- System Requirements 188
- ValVue SVi1000 Work 189
- Environment 189
- Working in SVi1000 190
- SVi1000 Help 191
- SVi1000 Tabs 192
- Trend Tab 193
- Configure Tab 194
- Calibrate Tab 195
- Status Tab 196
- ValVue SVi1000 197
- Figure 8 Check Tab 197
- Adjust Operations 200
- 2. Signal/Position Data 201
- 3. Status on the Monitor Tab 202
- Send Command drop down list 202
- 4. Information Pane 204
- Monitor Context Menu 205
- How to Create Reports 207
- Report Setup 211
- Generate Report 212
- Setup Wizard 213
- Setup Wizard Selections 214
- Positive Beta Negative Beta 223
- Configure 229
- Air Action 235
- Position Limits 236
- DO Output Switches 237
- Calibrate 241
- Figure 40 Calibrate Tab 242
- Calibration 243
- PID and Advanced Parameters 244
- Open Stop Adjustment 246
- Run Find Stops 248
- Manual Find Stops 250
- Auto Tune 251
- Active Faults 254
- General 255
- Figure 59 Status Tab: General 255
- Instrumentation 256
- Actuator 257
- Pneumatics 258
- Critical 259
- Electronics 260
- Fault Matrix 263
- Fault Matrix 265
- Optional Switch Load Limits 277
- Checking Switch Operation 279
- ValVue 12400 Software 281
- ValVue 12400 Work 283
- Working in ValVue 12400 285
- Tools Menu 286
- Modes of Operation 287
- Change Mode 288
- ValVue 12400 Help 291
- ValVue 12400 Screens 292
- Basic Setup 295
- Advanced Setup 296
- Transmitter Diagnostics 297
- Figure 87 Status Screen 298
- Figure 88 Check Screen 299
- Controller Monitor 300
- Controller Output 305
- Level Measurement 306
- Send Command 307
- PID Controller Mode 309
- 12400 Monitor Context Menu 310
- Restore 12400 Data 312
- Save 12400 Data 313
- English French 320
- Italian German 320
- Spanish Spanish 320
- Japanese Portuguese 320
- 12400 Monitor 323
- Level Indicator 324
- Send Command 331
- Command Selection 332
- Update Configured Data 334
- Controller Setup 335
- PID Controller Alarms 336
- PID Parameters Settings 337
- PID Controller Configuration 338
- PID Controller Setpoint Range 339
- Parameters include: 342
- Graph Display 344
- Changing the Graph View 345
- Detach Trend 347
- Capture to Clipboard 347
- Exiting in Setup Mode 350
- Transmitter 353
- Transmitter Mounting 354
- Transmitter Action 355
- Display Language 356
- Level Transmitter 357
- Applying Basic Setup Changes 361
- Basic Setup Context Menu 362
- SG Service 363
- Signal Range 365
- Local User Interface 368
- Changing Configuration 369
- SG Meter Calibration 370
- Reset to Factory 372
- Set SIL2 Settings 373
- Alarm Hysteresis 375
- Changing Level Units 377
- Zero Shift 378
- Reduced Span 378
- DO Switches 379
- Configuring DO Switches 380
- Configuring DO Switches 381
- Database 382
- Displacer Type 386
- Torque Tube and Chamber 387
- Chamber Options 392
- Applying Database Changes 394
- Filters and Tuning 395
- Smart Filter Enable 396
- Filter Parameters 397
- Autotune 400
- Calibration Filter 401
- Calibration Tools 403
- Signal Selection 404
- 4 - 20 mA Calibration 405
- Coupling 410
- Calibration Reset 411
- Advanced Setup Context Menu 415
- Diagnostics 417
- Continuous Diagnostic Data 418
- Service Time 420
- Set Interval 421
- Calibration Raw Range 423
- Specific Gravity Meter 424
- Specific Gravity Meter 425
- Log Only 429
- Annunciate 430
- User Faults 2 431
- Failsafe 432
- User Faults 1 433
- Clearing Faults 434
- Set Fail High/Fail Low 438
- Set Fail High/Fail Low 439
- ValVue VECTOR Software 443
- About This Manual 446
- Installation 447
- ValVue VECTOR 449
- Operational Overview 449
- Working in ValVue VECTOR 456
- ValVue VECTOR Help 456
- ValVue VECTOR Tabs 457
- Maintenance Tab 460
- Communication Tab 462
- Alerts Tab 463
- Battery Tab 464
- Run Setup Wizard 467
- Scan for Devices 468
- Figure 301 Trend Context Menu 471
- Configure Power Tab 474
- Configure Wireless Tab 477
- Join Mode 478
- Radio Power Output 478
- Radio Upgrade 478
- Over the Air Upgrade 478
- Configure Wired Tab 479
- Buttons and Fields 480
- Primary: This the default 480
- Secondary 480
- Configure 4-20 mA Tab 481
- Linear 482
- Special Curve 482
- Configure Burst Settings Tab 484
- Auto Burst 485
- Automatic Update 485
- Burst Command 487
- Configure Auto Burst 489
- Configure Manual Burst 489
- Configure Adapter Info Tab 495
- Configure Adapter Info Tab 497
- Configure Time Screen 498
- Maintenance 501
- Status Screen: General 505
- Device_Status 507
- IO_and_Subdevice_Status 508
- Ext_Device_Status 509
- WirelessHART_Status 510
- Device_Diagnostic_Status_0 511
- Device_Specific_Status_0 512
- Device_Specific_Status_1 513
- Communication 515
- Communication Tab 517
- Battery Info Screen 521
- to apply changes 522
- ValVue HDLT Software 525
- Monitor Tab 527
- Menu - Monitor 534
- Configuration Tab 536
- Menu - Configure 539
- Calibration Tab 540
- Level Transmitter Calibration 541
- Menu - Calibrate 541
- Calibration Parameters Tab 542
- Calibration Tools Tab 544
- Controller Parameters Tab 546
- Menu - Controller 548
- Controller Tab 549
- Configuration DataBase Tab 551
- Transmitter Diagnostics Tab 553
- Menu - Diagnostics 554
- Menu Bar and Footer Buttons 555
- ValVue SVI Software 557
- Command Result Display 564
- Read Status 567
- Menu -Configure 577
- Controller Configure Tab 578
- Calibration Value 583
- Calibration Value- Pressure 584
- Diagnostics Tab 589
- Diagnostic Reports 595
- Menu -Status Tab 603
- Check Tab 604
- Menu-Check 605
- Controller Settings Tab 609
- Custom Characterization 631
- Linearization 632
- Configure 633
- Menu - Check 656
- DIRECT SALES OFFICE LOCATIONS 660
Produits connexes et manuels pour Mesure, test et contrôle GE MN-ValVue-v2-8-IOM
(297 pages)
(68 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.133 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels